Forum Debian Users Gang

Miziak · 2013-11-26 21:53:38

Witam do wczoraj kiedy zaktualizowałem wspomniana technologia działała(przez bumblebee) gorzej czy lepiej nie ma znaczenia ale działała. Po aktualizacji systemu nie wstał mi xserver ale przeinstalowałem je i znów ładnie wstały ale kiedy chciałem odpalić grę na wine ona nie wstała, więc sprawdziłem polecenie:

Kod:

optirun glxgears

Na początku wywaliło coś o nieznanym sterowniku ale o tym było na wiki debiana wystarczyło zamienić nvidia na nvidia-current.
Ale mimo to to nie rozwiązało problemu utknąłem na kolejnym błędzie:

Kod:

miziak@debian:~$ optirun glxgears
[ 1306.200042] [ERROR]Cannot access secondary GPU - error: [XORG] (EE) NVIDIA(0): Failed to initialize the NVIDIA kernel module. Please see the

[ 1306.200086] [ERROR]Aborting because fallback start is disabled.

Kilka informacji na temat systemu/sprzętu:

Kod:

miziak@debian:~$ lspci | grep VGA
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
01:00.0 VGA compatible controller: NVIDIA Corporation GK107M [GeForce GT 645M] (rev a1)

Kod:

miziak@debian:~$ lsmod | grep nv
nvidia               9438739  0 
i2c_core               24084  7 drm,i915,i2c_i801,drm_kms_helper,i2c_algo_bit,nvidia,videodev
miziak@debian:~$ lsmod | grep no[/quote]
[quote]miziak@debian:~$ uname -a
Linux debian 3.11-2-amd64 #1 SMP Debian 3.11.8-1 (2013-11-13) x86_64 GNU/Linux

Kod:

miziak@debian:~$ cat /var/log/Xorg.0.log
[    24.085] 
X.Org X Server 1.14.3
Release Date: 2013-09-12
[    24.085] X Protocol Version 11, Revision 0
[    24.085] Build Operating System: Linux 3.10-2-amd64 x86_64 Debian
[    24.085] Current Operating System: Linux debian 3.11-2-amd64 #1 SMP Debian 3.11.8-1 (2013-11-13) x86_64
[    24.085] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.11-2-amd64 root=UUID=8c7f039c-af9a-4bfd-a23d-1c8a58231204 ro quiet
[    24.085] Build Date: 05 October 2013  02:04:26PM
[    24.085] xorg-server 2:1.14.3-4 (Julien Cristau <jcristau@debian.org>) 
[    24.085] Current version of pixman: 0.30.2
[    24.085]     Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
[    24.085] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    24.085] (==) Log file: "/var/log/Xorg.0.log", Time: Tue Nov 26 21:23:29 2013
[    24.248] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    24.310] (==) No Layout section.  Using the first Screen section.
[    24.310] (==) No screen section available. Using defaults.
[    24.310] (**) |-->Screen "Default Screen Section" (0)
[    24.310] (**) |   |-->Monitor "<default monitor>"
[    24.326] (==) No monitor specified for screen "Default Screen Section".
    Using a default monitor configuration.
[    24.326] (==) Automatically adding devices
[    24.326] (==) Automatically enabling devices
[    24.326] (==) Automatically adding GPU devices
[    24.395] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    24.395]     Entry deleted from font path.
[    24.395] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[    24.395]     Entry deleted from font path.
[    24.395] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[    24.395]     Entry deleted from font path.
[    24.422] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[    24.422]     Entry deleted from font path.
[    24.422] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[    24.422]     Entry deleted from font path.
[    24.422] (==) FontPath set to:
    /usr/share/fonts/X11/misc,
    /usr/share/fonts/X11/Type1,
    built-ins
[    24.422] (==) ModulePath set to "/usr/lib/xorg/modules"
[    24.422] (II) The server relies on udev to provide the list of input devices.
    If no devices become available, reconfigure udev or disable AutoAddDevices.
[    24.432] (II) Loader magic: 0x7fd6d8fa0d00
[    24.432] (II) Module ABI versions:
[    24.432]     X.Org ANSI C Emulation: 0.4
[    24.432]     X.Org Video Driver: 14.1
[    24.432]     X.Org XInput driver : 19.1
[    24.432]     X.Org Server Extension : 7.0
[    24.432] (II) xfree86: Adding drm device (/dev/dri/card0)
[    24.433] (--) PCI:*(0:0:2:0) 8086:0166:17aa:3904 rev 9, Mem @ 0xd3000000/4194304, 0xe0000000/268435456, I/O @ 0x00004000/64
[    24.434] (II) Open ACPI successful (/var/run/acpid.socket)
[    24.434] Initializing built-in extension Generic Event Extension
[    24.434] Initializing built-in extension SHAPE
[    24.434] Initializing built-in extension MIT-SHM
[    24.434] Initializing built-in extension XInputExtension
[    24.434] Initializing built-in extension XTEST
[    24.434] Initializing built-in extension BIG-REQUESTS
[    24.434] Initializing built-in extension SYNC
[    24.434] Initializing built-in extension XKEYBOARD
[    24.434] Initializing built-in extension XC-MISC
[    24.434] Initializing built-in extension SECURITY
[    24.434] Initializing built-in extension XINERAMA
[    24.434] Initializing built-in extension XFIXES
[    24.434] Initializing built-in extension RENDER
[    24.434] Initializing built-in extension RANDR
[    24.434] Initializing built-in extension COMPOSITE
[    24.434] Initializing built-in extension DAMAGE
[    24.434] Initializing built-in extension MIT-SCREEN-SAVER
[    24.434] Initializing built-in extension DOUBLE-BUFFER
[    24.434] Initializing built-in extension RECORD
[    24.434] Initializing built-in extension DPMS
[    24.434] Initializing built-in extension X-Resource
[    24.434] Initializing built-in extension XVideo
[    24.434] Initializing built-in extension XVideo-MotionCompensation
[    24.434] Initializing built-in extension SELinux
[    24.434] Initializing built-in extension XFree86-VidModeExtension
[    24.434] Initializing built-in extension XFree86-DGA
[    24.434] Initializing built-in extension XFree86-DRI
[    24.434] Initializing built-in extension DRI2
[    24.434] (II) LoadModule: "glx"
[    24.484] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    24.499] (II) Module glx: vendor="X.Org Foundation"
[    24.500]     compiled for 1.14.3, module version = 1.0.0
[    24.500]     ABI class: X.Org Server Extension, version 7.0
[    24.500] (==) AIGLX enabled
[    24.500] Loading extension GLX
[    24.500] (==) Matched intel as autoconfigured driver 0
[    24.500] (==) Matched intel as autoconfigured driver 1
[    24.500] (==) Matched vesa as autoconfigured driver 2
[    24.500] (==) Matched modesetting as autoconfigured driver 3
[    24.500] (==) Matched fbdev as autoconfigured driver 4
[    24.500] (==) Assigned the driver to the xf86ConfigLayout
[    24.500] (II) LoadModule: "intel"
[    24.500] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[    24.601] (II) Module intel: vendor="X.Org Foundation"
[    24.601]     compiled for 1.14.3, module version = 2.21.15
[    24.601]     Module class: X.Org Video Driver
[    24.601]     ABI class: X.Org Video Driver, version 14.1
[    24.601] (II) LoadModule: "vesa"
[    24.601] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[    24.619] (II) Module vesa: vendor="X.Org Foundation"
[    24.619]     compiled for 1.14.3, module version = 2.3.3
[    24.619]     Module class: X.Org Video Driver
[    24.619]     ABI class: X.Org Video Driver, version 14.1
[    24.619] (II) LoadModule: "modesetting"
[    24.619] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[    24.638] (II) Module modesetting: vendor="X.Org Foundation"
[    24.638]     compiled for 1.14.3, module version = 0.8.0
[    24.638]     Module class: X.Org Video Driver
[    24.638]     ABI class: X.Org Video Driver, version 14.1
[    24.638] (II) LoadModule: "fbdev"
[    24.639] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[    24.653] (II) Module fbdev: vendor="X.Org Foundation"
[    24.653]     compiled for 1.14.3, module version = 0.4.4
[    24.653]     Module class: X.Org Video Driver
[    24.653]     ABI class: X.Org Video Driver, version 14.1
[    24.653] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
    i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
    915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
    Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
    GM45, 4 Series, G45/G43, Q45/Q43, G41, B43, HD Graphics,
    HD Graphics 2000, HD Graphics 3000, HD Graphics 2500,
    HD Graphics 4000, HD Graphics P4000, HD Graphics 4600,
    HD Graphics 5000, HD Graphics P4600/P4700, Iris(TM) Graphics 5100,
    HD Graphics 4400, HD Graphics 4200, Iris(TM) Pro Graphics 5200
[    24.654] (II) VESA: driver for VESA chipsets: vesa
[    24.654] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[    24.654] (II) FBDEV: driver for framebuffer: fbdev
[    24.654] (++) using VT number 7

[    24.697] (WW) Falling back to old probe method for vesa
[    24.697] (WW) Falling back to old probe method for modesetting
[    24.697] (WW) Falling back to old probe method for fbdev
[    24.697] (II) Loading sub module "fbdevhw"
[    24.697] (II) LoadModule: "fbdevhw"
[    24.697] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[    24.706] (II) Module fbdevhw: vendor="X.Org Foundation"
[    24.706]     compiled for 1.14.3, module version = 0.0.2
[    24.706]     ABI class: X.Org Video Driver, version 14.1
[    24.707] (II) intel(0): Creating default Display subsection in Screen section
    "Default Screen Section" for depth/fbbpp 24/32
[    24.707] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[    24.707] (==) intel(0): RGB weight 888
[    24.707] (==) intel(0): Default visual is TrueColor
[    24.707] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics 4000
[    24.707] (**) intel(0): Relaxed fencing enabled
[    24.707] (**) intel(0): Wait on SwapBuffers? enabled
[    24.707] (**) intel(0): Triple buffering? enabled
[    24.707] (**) intel(0): Framebuffer tiled
[    24.707] (**) intel(0): Pixmaps tiled
[    24.707] (**) intel(0): 3D buffers tiled
[    24.707] (**) intel(0): SwapBuffers wait enabled
[    24.707] (==) intel(0): video overlay key set to 0x101fe
[    24.707] (II) intel(0): Output LVDS1 has no monitor section
[    24.707] (--) intel(0): found backlight control interface /sys/class/backlight/acpi_video1
[    24.708] (II) intel(0): Output VGA1 has no monitor section
[    24.708] (II) intel(0): Output HDMI1 has no monitor section
[    24.709] (II) intel(0): Output DP1 has no monitor section
[    24.709] (II) intel(0): EDID for output LVDS1
[    24.709] (II) intel(0): Manufacturer: CMN  Model: 15b5  Serial#: 0
[    24.709] (II) intel(0): Year: 2012  Week: 2
[    24.709] (II) intel(0): EDID Version: 1.3
[    24.709] (II) intel(0): Digital Display Input
[    24.709] (II) intel(0): Max Image Size [cm]: horiz.: 34  vert.: 19
[    24.709] (II) intel(0): Gamma: 2.20
[    24.709] (II) intel(0): No DPMS capabilities specified
[    24.709] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 
[    24.709] (II) intel(0): First detailed timing is preferred mode
[    24.709] (II) intel(0): redX: 0.577 redY: 0.364   greenX: 0.348 greenY: 0.563
[    24.709] (II) intel(0): blueX: 0.151 blueY: 0.116   whiteX: 0.313 whiteY: 0.329
[    24.709] (II) intel(0): Manufacturer's mask: 0
[    24.709] (II) intel(0): Supported detailed timing:
[    24.709] (II) intel(0): clock: 76.4 MHz   Image Size:  344 x 194 mm
[    24.709] (II) intel(0): h_active: 1366  h_sync: 1434  h_sync_end 1480 h_blank_end 1592 h_border: 0
[    24.709] (II) intel(0): v_active: 768  v_sync: 772  v_sync_end 778 v_blanking: 799 v_border: 0
[    24.709] (II) intel(0):  CMN
[    24.709] (II) intel(0):  N156BGE-LA1
[    24.709] (II) intel(0): EDID (in hex):
[    24.709] (II) intel(0):     00ffffffffffff000daeb51500000000
[    24.709] (II) intel(0):     02160103802213780ad1f5935d599026
[    24.709] (II) intel(0):     1d505400000001010101010101010101
[    24.709] (II) intel(0):     010101010101d81d56e250001f30442e
[    24.709] (II) intel(0):     460058c210000018a60000fe004e3135
[    24.709] (II) intel(0):     364247452d4c41310a20000000fe0043
[    24.709] (II) intel(0):     4d4e0a202020202020202020000000fe
[    24.709] (II) intel(0):     004e3135364247452d4c41310a200090
[    24.709] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "720x450" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "800x512" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "960x540" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "960x600" (doublescan mode not supported)
[    24.709] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[    24.709] (II) intel(0): Printing probed modes for output LVDS1
[    24.709] (II) intel(0): Modeline "1366x768"x60.1   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)
[    24.709] (II) intel(0): Modeline "1360x768"x59.8   84.75  1360 1432 1568 1776  768 771 781 798 -hsync +vsync (47.7 kHz d)
[    24.709] (II) intel(0): Modeline "1360x768"x60.0   72.00  1360 1408 1440 1520  768 771 781 790 +hsync -vsync (47.4 kHz d)
[    24.709] (II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz d)
[    24.709] (II) intel(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz d)
[    24.709] (II) intel(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz d)
[    24.709] (II) intel(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz d)
[    24.710] (II) intel(0): EDID for output VGA1
[    24.711] (II) intel(0): EDID for output HDMI1
[    24.711] (II) intel(0): EDID for output DP1
[    24.711] (II) intel(0): Output LVDS1 connected
[    24.711] (II) intel(0): Output VGA1 disconnected
[    24.711] (II) intel(0): Output HDMI1 disconnected
[    24.711] (II) intel(0): Output DP1 disconnected
[    24.711] (II) intel(0): Using exact sizes for initial modes
[    24.711] (II) intel(0): Output LVDS1 using initial mode 1366x768
[    24.711] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[    24.711] (II) intel(0): Kernel page flipping support detected, enabling
[    24.711] (==) intel(0): DPI set to (96, 96)
[    24.711] (II) Loading sub module "fb"
[    24.711] (II) LoadModule: "fb"
[    24.711] (II) Loading /usr/lib/xorg/modules/libfb.so
[    24.726] (II) Module fb: vendor="X.Org Foundation"
[    24.726]     compiled for 1.14.3, module version = 1.0.0
[    24.726]     ABI class: X.Org ANSI C Emulation, version 0.4
[    24.726] (II) Loading sub module "dri2"
[    24.726] (II) LoadModule: "dri2"
[    24.726] (II) Module "dri2" already built-in
[    24.726] (II) UnloadModule: "vesa"
[    24.726] (II) Unloading vesa
[    24.726] (II) UnloadModule: "modesetting"
[    24.726] (II) Unloading modesetting
[    24.726] (II) UnloadModule: "fbdev"
[    24.726] (II) Unloading fbdev
[    24.726] (II) UnloadSubModule: "fbdevhw"
[    24.727] (II) Unloading fbdevhw
[    24.727] (==) Depth 24 pixmap format is 32 bpp
[    24.730] (II) intel(0): [DRI2] Setup complete
[    24.730] (II) intel(0): [DRI2]   DRI driver: i965
[    24.730] (II) intel(0): Allocated new frame buffer 1408x768 stride 5632, tiled
[    24.739] (II) UXA(0): Driver registered support for the following operations:
[    24.739] (II)         solid
[    24.739] (II)         copy
[    24.739] (II)         composite (RENDER acceleration)
[    24.739] (II)         put_image
[    24.739] (II)         get_image
[    24.739] (==) intel(0): Backing store disabled
[    24.739] (==) intel(0): Silken mouse enabled
[    24.739] (II) intel(0): Initializing HW Cursor
[    24.739] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    24.740] (==) intel(0): DPMS enabled
[    24.741] (==) intel(0): Intel XvMC decoder enabled
[    24.741] (II) intel(0): Set up textured video
[    24.741] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[    24.741] (II) intel(0): direct rendering: DRI2 Enabled
[    24.741] (==) intel(0): hotplug detection: "enabled"
[    24.760] (--) RandR disabled
[    24.887] (II) SELinux: Disabled on system
[    25.331] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[    25.331] (II) AIGLX: enabled GLX_INTEL_swap_event
[    25.331] (II) AIGLX: enabled GLX_ARB_create_context
[    25.331] (II) AIGLX: enabled GLX_ARB_create_context_profile
[    25.331] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[    25.331] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[    25.331] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[    25.331] (II) AIGLX: Loaded and initialized i965
[    25.331] (II) GLX: Initialized DRI2 GL provider for screen 0
[    25.331] (II) intel(0): Setting screen physical size to 361 x 203
[    26.641] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[    26.641] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    26.641] (II) LoadModule: "evdev"
[    26.659] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    26.701] (II) Module evdev: vendor="X.Org Foundation"
[    26.701]     compiled for 1.14.3, module version = 2.8.2
[    26.701]     Module class: X.Org XInput Driver
[    26.701]     ABI class: X.Org XInput driver, version 19.1
[    26.701] (II) Using input driver 'evdev' for 'Power Button'
[    26.701] (**) Power Button: always reports core events
[    26.701] (**) evdev: Power Button: Device: "/dev/input/event3"
[    26.701] (--) evdev: Power Button: Vendor 0 Product 0x1
[    26.701] (--) evdev: Power Button: Found keys
[    26.701] (II) evdev: Power Button: Configuring as keyboard
[    26.701] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"
[    26.701] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    26.701] (**) Option "xkb_rules" "evdev"
[    26.701] (**) Option "xkb_model" "pc105"
[    26.701] (**) Option "xkb_layout" "pl"
[    27.012] (II) config/udev: Adding input device Video Bus (/dev/input/event13)
[    27.012] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[    27.012] (II) Using input driver 'evdev' for 'Video Bus'
[    27.012] (**) Video Bus: always reports core events
[    27.012] (**) evdev: Video Bus: Device: "/dev/input/event13"
[    27.012] (--) evdev: Video Bus: Vendor 0 Product 0x6
[    27.012] (--) evdev: Video Bus: Found keys
[    27.012] (II) evdev: Video Bus: Configuring as keyboard
[    27.012] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input13/event13"
[    27.012] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[    27.012] (**) Option "xkb_rules" "evdev"
[    27.012] (**) Option "xkb_model" "pc105"
[    27.012] (**) Option "xkb_layout" "pl"
[    27.013] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[    27.013] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    27.013] (II) Using input driver 'evdev' for 'Power Button'
[    27.013] (**) Power Button: always reports core events
[    27.013] (**) evdev: Power Button: Device: "/dev/input/event1"
[    27.013] (--) evdev: Power Button: Vendor 0 Product 0x1
[    27.013] (--) evdev: Power Button: Found keys
[    27.013] (II) evdev: Power Button: Configuring as keyboard
[    27.013] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0C:00/input/input1/event1"
[    27.013] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[    27.013] (**) Option "xkb_rules" "evdev"
[    27.013] (**) Option "xkb_model" "pc105"
[    27.013] (**) Option "xkb_layout" "pl"
[    27.014] (II) config/udev: Adding input device Video Bus (/dev/input/event11)
[    27.014] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[    27.014] (II) Using input driver 'evdev' for 'Video Bus'
[    27.014] (**) Video Bus: always reports core events
[    27.014] (**) evdev: Video Bus: Device: "/dev/input/event11"
[    27.014] (--) evdev: Video Bus: Vendor 0 Product 0x6
[    27.014] (--) evdev: Video Bus: Found keys
[    27.014] (II) evdev: Video Bus: Configuring as keyboard
[    27.014] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:36/LNXVIDEO:00/input/input11/event11"
[    27.014] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 9)
[    27.014] (**) Option "xkb_rules" "evdev"
[    27.014] (**) Option "xkb_model" "pc105"
[    27.014] (**) Option "xkb_layout" "pl"
[    27.014] (II) config/udev: Adding input device Lid Switch (/dev/input/event2)
[    27.014] (II) No input driver specified, ignoring this device.
[    27.014] (II) This device may have been added with another device file.
[    27.014] (II) config/udev: Adding drm device (/dev/dri/card0)
[    27.015] (II) config/udev: Adding input device Lenovo EasyCamera (/dev/input/event12)
[    27.015] (**) Lenovo EasyCamera: Applying InputClass "evdev keyboard catchall"
[    27.015] (II) Using input driver 'evdev' for 'Lenovo EasyCamera'
[    27.015] (**) Lenovo EasyCamera: always reports core events
[    27.015] (**) evdev: Lenovo EasyCamera: Device: "/dev/input/event12"
[    27.015] (--) evdev: Lenovo EasyCamera: Vendor 0x4f2 Product 0xb35d
[    27.015] (--) evdev: Lenovo EasyCamera: Found keys
[    27.015] (II) evdev: Lenovo EasyCamera: Configuring as keyboard
[    27.015] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.0/input/input12/event12"
[    27.015] (II) XINPUT: Adding extended input device "Lenovo EasyCamera" (type: KEYBOARD, id 10)
[    27.015] (**) Option "xkb_rules" "evdev"
[    27.015] (**) Option "xkb_model" "pc105"
[    27.015] (**) Option "xkb_layout" "pl"
[    27.015] (II) config/udev: Adding input device RAPOO RAPOO 5G Wireless Device (/dev/input/event14)
[    27.015] (**) RAPOO RAPOO 5G Wireless Device: Applying InputClass "evdev keyboard catchall"
[    27.016] (II) Using input driver 'evdev' for 'RAPOO RAPOO 5G Wireless Device'
[    27.016] (**) RAPOO RAPOO 5G Wireless Device: always reports core events
[    27.016] (**) evdev: RAPOO RAPOO 5G Wireless Device: Device: "/dev/input/event14"
[    27.016] (--) evdev: RAPOO RAPOO 5G Wireless Device: Vendor 0x24ae Product 0x2001
[    27.016] (--) evdev: RAPOO RAPOO 5G Wireless Device: Found keys
[    27.016] (II) evdev: RAPOO RAPOO 5G Wireless Device: Configuring as keyboard
[    27.016] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/input/input14/event14"
[    27.016] (II) XINPUT: Adding extended input device "RAPOO RAPOO 5G Wireless Device" (type: KEYBOARD, id 11)
[    27.016] (**) Option "xkb_rules" "evdev"
[    27.016] (**) Option "xkb_model" "pc105"
[    27.016] (**) Option "xkb_layout" "pl"
[    27.016] (II) config/udev: Adding input device RAPOO RAPOO 5G Wireless Device (/dev/input/event15)
[    27.016] (**) RAPOO RAPOO 5G Wireless Device: Applying InputClass "evdev pointer catchall"
[    27.016] (**) RAPOO RAPOO 5G Wireless Device: Applying InputClass "evdev keyboard catchall"
[    27.016] (II) Using input driver 'evdev' for 'RAPOO RAPOO 5G Wireless Device'
[    27.016] (**) RAPOO RAPOO 5G Wireless Device: always reports core events
[    27.016] (**) evdev: RAPOO RAPOO 5G Wireless Device: Device: "/dev/input/event15"
[    27.016] (--) evdev: RAPOO RAPOO 5G Wireless Device: Vendor 0x24ae Product 0x2001
[    27.016] (--) evdev: RAPOO RAPOO 5G Wireless Device: Found 9 mouse buttons
[    27.016] (--) evdev: RAPOO RAPOO 5G Wireless Device: Found scroll wheel(s)
[    27.016] (--) evdev: RAPOO RAPOO 5G Wireless Device: Found relative axes
[    27.016] (--) evdev: RAPOO RAPOO 5G Wireless Device: Found x and y relative axes
[    27.016] (--) evdev: RAPOO RAPOO 5G Wireless Device: Found absolute axes
[    27.016] (II) evdev: RAPOO RAPOO 5G Wireless Device: Forcing absolute x/y axes to exist.
[    27.017] (--) evdev: RAPOO RAPOO 5G Wireless Device: Found keys
[    27.017] (II) evdev: RAPOO RAPOO 5G Wireless Device: Configuring as mouse
[    27.017] (II) evdev: RAPOO RAPOO 5G Wireless Device: Configuring as keyboard
[    27.017] (II) evdev: RAPOO RAPOO 5G Wireless Device: Adding scrollwheel support
[    27.017] (**) evdev: RAPOO RAPOO 5G Wireless Device: YAxisMapping: buttons 4 and 5
[    27.017] (**) evdev: RAPOO RAPOO 5G Wireless Device: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    27.017] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.1/input/input15/event15"
[    27.017] (II) XINPUT: Adding extended input device "RAPOO RAPOO 5G Wireless Device" (type: KEYBOARD, id 12)
[    27.017] (**) Option "xkb_rules" "evdev"
[    27.017] (**) Option "xkb_model" "pc105"
[    27.017] (**) Option "xkb_layout" "pl"
[    27.017] (II) evdev: RAPOO RAPOO 5G Wireless Device: initialized for relative axes.
[    27.017] (WW) evdev: RAPOO RAPOO 5G Wireless Device: ignoring absolute axes.
[    27.017] (**) RAPOO RAPOO 5G Wireless Device: (accel) keeping acceleration scheme 1
[    27.017] (**) RAPOO RAPOO 5G Wireless Device: (accel) acceleration profile 0
[    27.017] (**) RAPOO RAPOO 5G Wireless Device: (accel) acceleration factor: 2.000
[    27.017] (**) RAPOO RAPOO 5G Wireless Device: (accel) acceleration threshold: 4
[    27.017] (II) config/udev: Adding input device RAPOO RAPOO 5G Wireless Device (/dev/input/mouse1)
[    27.018] (II) No input driver specified, ignoring this device.
[    27.018] (II) This device may have been added with another device file.
[    27.018] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event6)
[    27.018] (II) No input driver specified, ignoring this device.
[    27.018] (II) This device may have been added with another device file.
[    27.018] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event7)
[    27.018] (II) No input driver specified, ignoring this device.
[    27.018] (II) This device may have been added with another device file.
[    27.018] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event8)
[    27.018] (II) No input driver specified, ignoring this device.
[    27.018] (II) This device may have been added with another device file.
[    27.018] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event9)
[    27.018] (II) No input driver specified, ignoring this device.
[    27.018] (II) This device may have been added with another device file.
[    27.019] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[    27.019] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[    27.019] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[    27.019] (**) AT Translated Set 2 keyboard: always reports core events
[    27.019] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[    27.019] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[    27.019] (--) evdev: AT Translated Set 2 keyboard: Found keys
[    27.019] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[    27.019] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[    27.019] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 13)
[    27.019] (**) Option "xkb_rules" "evdev"
[    27.019] (**) Option "xkb_model" "pc105"
[    27.019] (**) Option "xkb_layout" "pl"
[    27.019] (II) config/udev: Adding input device ETPS/2 Elantech Touchpad (/dev/input/event10)
[    27.019] (**) ETPS/2 Elantech Touchpad: Applying InputClass "evdev touchpad catchall"
[    27.019] (**) ETPS/2 Elantech Touchpad: Applying InputClass "touchpad catchall"
[    27.019] (**) ETPS/2 Elantech Touchpad: Applying InputClass "Default clickpad buttons"
[    27.019] (II) LoadModule: "synaptics"
[    27.020] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[    27.127] (II) Module synaptics: vendor="X.Org Foundation"
[    27.127]     compiled for 1.14.3, module version = 1.7.1
[    27.127]     Module class: X.Org XInput Driver
[    27.127]     ABI class: X.Org XInput driver, version 19.1
[    27.127] (II) Using input driver 'synaptics' for 'ETPS/2 Elantech Touchpad'
[    27.127] (**) ETPS/2 Elantech Touchpad: always reports core events
[    27.127] (**) Option "Device" "/dev/input/event10"
[    27.220] (II) synaptics: ETPS/2 Elantech Touchpad: found clickpad property
[    27.220] (--) synaptics: ETPS/2 Elantech Touchpad: x-axis range 0 - 3260 (res 33)
[    27.220] (--) synaptics: ETPS/2 Elantech Touchpad: y-axis range 0 - 2119 (res 33)
[    27.220] (--) synaptics: ETPS/2 Elantech Touchpad: pressure range 0 - 255
[    27.220] (--) synaptics: ETPS/2 Elantech Touchpad: finger width range 0 - 15
[    27.220] (--) synaptics: ETPS/2 Elantech Touchpad: buttons: left double triple
[    27.220] (--) synaptics: ETPS/2 Elantech Touchpad: Vendor 0x2 Product 0xe
[    27.220] (**) Option "SoftButtonAreas" "50% 0 82% 0 0 0 0 0"
[    27.220] (--) synaptics: ETPS/2 Elantech Touchpad: touchpad found
[    27.220] (**) ETPS/2 Elantech Touchpad: always reports core events
[    27.300] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input10/event10"
[    27.300] (II) XINPUT: Adding extended input device "ETPS/2 Elantech Touchpad" (type: TOUCHPAD, id 14)
[    27.300] (**) synaptics: ETPS/2 Elantech Touchpad: (accel) MinSpeed is now constant deceleration 2.5
[    27.300] (**) synaptics: ETPS/2 Elantech Touchpad: (accel) MaxSpeed is now 1.75
[    27.300] (**) synaptics: ETPS/2 Elantech Touchpad: (accel) AccelFactor is now 0.051
[    27.300] (**) ETPS/2 Elantech Touchpad: (accel) keeping acceleration scheme 1
[    27.300] (**) ETPS/2 Elantech Touchpad: (accel) acceleration profile 1
[    27.300] (**) ETPS/2 Elantech Touchpad: (accel) acceleration factor: 2.000
[    27.300] (**) ETPS/2 Elantech Touchpad: (accel) acceleration threshold: 4
[    27.300] (--) synaptics: ETPS/2 Elantech Touchpad: touchpad found
[    27.301] (II) config/udev: Adding input device ETPS/2 Elantech Touchpad (/dev/input/mouse0)
[    27.301] (**) ETPS/2 Elantech Touchpad: Ignoring device from InputClass "touchpad ignore duplicates"
[    27.301] (II) config/udev: Adding input device Ideapad extra buttons (/dev/input/event5)
[    27.301] (**) Ideapad extra buttons: Applying InputClass "evdev keyboard catchall"
[    27.301] (II) Using input driver 'evdev' for 'Ideapad extra buttons'
[    27.301] (**) Ideapad extra buttons: always reports core events
[    27.301] (**) evdev: Ideapad extra buttons: Device: "/dev/input/event5"
[    27.301] (--) evdev: Ideapad extra buttons: Vendor 0 Product 0
[    27.301] (--) evdev: Ideapad extra buttons: Found keys
[    27.301] (II) evdev: Ideapad extra buttons: Configuring as keyboard
[    27.301] (**) Option "config_info" "udev:/sys/devices/platform/ideapad/input/input5/event5"
[    27.301] (II) XINPUT: Adding extended input device "Ideapad extra buttons" (type: KEYBOARD, id 15)
[    27.301] (**) Option "xkb_rules" "evdev"
[    27.301] (**) Option "xkb_model" "pc105"
[    27.301] (**) Option "xkb_layout" "pl"
[    27.301] (II) config/udev: Adding input device PC Speaker (/dev/input/event4)
[    27.301] (II) No input driver specified, ignoring this device.
[    27.301] (II) This device may have been added with another device file.
[    35.102] (II) intel(0): EDID vendor "CMN", prod id 5557
[    35.102] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x846 mode
[    35.102] (II) intel(0): Printing DDC gathered Modelines:
[    35.102] (II) intel(0): Modeline "1366x768"x0.0   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)
[    41.659] (II) intel(0): EDID vendor "CMN", prod id 5557
[    41.659] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x846 mode
[    41.659] (II) intel(0): Printing DDC gathered Modelines:
[    41.659] (II) intel(0): Modeline "1366x768"x0.0   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)
[    42.184] (II) intel(0): EDID vendor "CMN", prod id 5557
[    42.184] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x846 mode
[    42.184] (II) intel(0): Printing DDC gathered Modelines:
[    42.184] (II) intel(0): Modeline "1366x768"x0.0   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)
[   104.125] (II) intel(0): EDID vendor "CMN", prod id 5557
[   104.125] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x846 mode
[   104.125] (II) intel(0): Printing DDC gathered Modelines:
[   104.125] (II) intel(0): Modeline "1366x768"x0.0   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)
[   106.231] (II) intel(0): EDID vendor "CMN", prod id 5557
[   106.231] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x846 mode
[   106.231] (II) intel(0): Printing DDC gathered Modelines:
[   106.231] (II) intel(0): Modeline "1366x768"x0.0   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)
[   106.286] (II) intel(0): EDID vendor "CMN", prod id 5557
[   106.286] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x846 mode
[   106.286] (II) intel(0): Printing DDC gathered Modelines:
[   106.286] (II) intel(0): Modeline "1366x768"x0.0   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)
[   150.225] (II) intel(0): EDID vendor "CMN", prod id 5557
[   150.225] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x846 mode
[   150.225] (II) intel(0): Printing DDC gathered Modelines:
[   150.225] (II) intel(0): Modeline "1366x768"x0.0   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)
[   150.372] (II) intel(0): EDID vendor "CMN", prod id 5557
[   150.372] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x846 mode
[   150.372] (II) intel(0): Printing DDC gathered Modelines:
[   150.372] (II) intel(0): Modeline "1366x768"x0.0   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)
[   150.477] (II) intel(0): Allocated new frame buffer 3328x1080 stride 13312, tiled
[   150.660] (II) intel(0): EDID vendor "CMN", prod id 5557
[   150.660] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x846 mode
[   150.660] (II) intel(0): Printing DDC gathered Modelines:
[   150.660] (II) intel(0): Modeline "1366x768"x0.0   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)
[   186.752] (II) intel(0): EDID vendor "CMN", prod id 5557
[   186.752] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x846 mode
[   186.752] (II) intel(0): Printing DDC gathered Modelines:
[   186.752] (II) intel(0): Modeline "1366x768"x0.0   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)
[   195.430] (II) intel(0): EDID vendor "CMN", prod id 5557
[   195.430] (II) intel(0): DDCModeFromDetailedTiming: Ignoring tiny 0x846 mode
[   195.430] (II) intel(0): Printing DDC gathered Modelines:
[   195.430] (II) intel(0): Modeline "1366x768"x0.0   76.40  1366 1434 1480 1592  768 772 778 799 -hsync -vsync (48.0 kHz eP)

Kod:

miziak@debian:~$ cat /var/log/Xorg.8.log
[  1304.521] 
X.Org X Server 1.14.3
Release Date: 2013-09-12
[  1304.521] X Protocol Version 11, Revision 0
[  1304.521] Build Operating System: Linux 3.10-2-amd64 x86_64 Debian
[  1304.521] Current Operating System: Linux debian 3.11-2-amd64 #1 SMP Debian 3.11.8-1 (2013-11-13) x86_64
[  1304.521] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.11-2-amd64 root=UUID=8c7f039c-af9a-4bfd-a23d-1c8a58231204 ro quiet
[  1304.521] Build Date: 05 October 2013  02:04:26PM
[  1304.521] xorg-server 2:1.14.3-4 (Julien Cristau <jcristau@debian.org>) 
[  1304.521] Current version of pixman: 0.30.2
[  1304.521]     Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
[  1304.521] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[  1304.521] (==) Log file: "/var/log/Xorg.8.log", Time: Tue Nov 26 21:44:49 2013
[  1304.534] (++) Using config file: "/etc/bumblebee/xorg.conf.nvidia"
[  1304.534] (++) Using config directory: "/etc/bumblebee/xorg.conf.d"
[  1304.534] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[  1304.544] (==) ServerLayout "Layout0"
[  1304.544] (==) No screen section available. Using defaults.
[  1304.544] (**) |-->Screen "Default Screen Section" (0)
[  1304.544] (**) |   |-->Monitor "<default monitor>"
[  1304.545] (==) No device specified for screen "Default Screen Section".
    Using the first device section listed.
[  1304.545] (**) |   |-->Device "DiscreteNvidia"
[  1304.545] (==) No monitor specified for screen "Default Screen Section".
    Using a default monitor configuration.
[  1304.545] (**) Option "AutoAddDevices" "false"
[  1304.545] (**) Option "AutoAddGPU" "false"
[  1304.545] (**) Not automatically adding devices
[  1304.545] (==) Automatically enabling devices
[  1304.545] (**) Not automatically adding GPU devices
[  1304.545] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[  1304.545]     Entry deleted from font path.
[  1304.545] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[  1304.545]     Entry deleted from font path.
[  1304.545] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[  1304.545]     Entry deleted from font path.
[  1304.545] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[  1304.545]     Entry deleted from font path.
[  1304.545] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[  1304.545]     Entry deleted from font path.
[  1304.545] (==) FontPath set to:
    /usr/share/fonts/X11/misc,
    /usr/share/fonts/X11/Type1,
    built-ins
[  1304.545] (++) ModulePath set to "/usr/lib/nvidia,/usr/lib/xorg/modules"
[  1304.545] (==) |-->Input Device "<default pointer>"
[  1304.545] (==) |-->Input Device "<default keyboard>"
[  1304.545] (==) The core pointer device wasn't specified explicitly in the layout.
    Using the default mouse configuration.
[  1304.545] (==) The core keyboard device wasn't specified explicitly in the layout.
    Using the default keyboard configuration.
[  1304.545] (II) Loader magic: 0x7fb568b87d00
[  1304.545] (II) Module ABI versions:
[  1304.545]     X.Org ANSI C Emulation: 0.4
[  1304.545]     X.Org Video Driver: 14.1
[  1304.545]     X.Org XInput driver : 19.1
[  1304.545]     X.Org Server Extension : 7.0
[  1304.545] (II) xfree86: Adding drm device (/dev/dri/card0)
[  1304.545] setversion 1.4 failed
[  1304.546] (--) PCI:*(0:1:0:0) 10de:0fd9:17aa:3904 rev 161, Mem @ 0xd2000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x00003000/128
[  1304.546] (II) Open ACPI successful (/var/run/acpid.socket)
[  1304.546] Initializing built-in extension Generic Event Extension
[  1304.546] Initializing built-in extension SHAPE
[  1304.546] Initializing built-in extension MIT-SHM
[  1304.546] Initializing built-in extension XInputExtension
[  1304.546] Initializing built-in extension XTEST
[  1304.546] Initializing built-in extension BIG-REQUESTS
[  1304.546] Initializing built-in extension SYNC
[  1304.546] Initializing built-in extension XKEYBOARD
[  1304.546] Initializing built-in extension XC-MISC
[  1304.546] Initializing built-in extension SECURITY
[  1304.546] Initializing built-in extension XINERAMA
[  1304.546] Initializing built-in extension XFIXES
[  1304.546] Initializing built-in extension RENDER
[  1304.546] Initializing built-in extension RANDR
[  1304.546] Initializing built-in extension COMPOSITE
[  1304.546] Initializing built-in extension DAMAGE
[  1304.546] Initializing built-in extension MIT-SCREEN-SAVER
[  1304.546] Initializing built-in extension DOUBLE-BUFFER
[  1304.546] Initializing built-in extension RECORD
[  1304.546] Initializing built-in extension DPMS
[  1304.546] Initializing built-in extension X-Resource
[  1304.546] Initializing built-in extension XVideo
[  1304.546] Initializing built-in extension XVideo-MotionCompensation
[  1304.546] Initializing built-in extension SELinux
[  1304.546] Initializing built-in extension XFree86-VidModeExtension
[  1304.546] Initializing built-in extension XFree86-DGA
[  1304.546] Initializing built-in extension XFree86-DRI
[  1304.546] Initializing built-in extension DRI2
[  1304.546] (II) LoadModule: "glx"
[  1304.553] (II) Loading /usr/lib/nvidia/legacy-304xx/libglx.so
[  1305.959] (II) Module glx: vendor="NVIDIA Corporation"
[  1305.959]     compiled for 4.0.2, module version = 1.0.0
[  1305.959]     Module class: X.Org Server Extension
[  1305.959] (II) NVIDIA GLX Module  304.116  Mon Oct 28 20:59:08 PDT 2013
[  1305.959] Loading extension GLX
[  1305.959] (II) LoadModule: "nvidia"
[  1305.959] (II) Loading /usr/lib/nvidia/legacy-304xx/nvidia_drv.so
[  1306.062] (II) Module nvidia: vendor="NVIDIA Corporation"
[  1306.062]     compiled for 4.0.2, module version = 1.0.0
[  1306.062]     Module class: X.Org Video Driver
[  1306.130] (II) LoadModule: "mouse"
[  1306.131] (II) Loading /usr/lib/xorg/modules/input/mouse_drv.so
[  1306.138] (II) Module mouse: vendor="X.Org Foundation"
[  1306.138]     compiled for 1.14.3, module version = 1.9.0
[  1306.138]     Module class: X.Org XInput Driver
[  1306.138]     ABI class: X.Org XInput driver, version 19.1
[  1306.138] (II) LoadModule: "kbd"
[  1306.139] (WW) Warning, couldn't open module kbd
[  1306.139] (II) UnloadModule: "kbd"
[  1306.139] (II) Unloading kbd
[  1306.139] (EE) Failed to load module "kbd" (module does not exist, 0)
[  1306.139] (II) NVIDIA dlloader X Driver  304.116  Mon Oct 28 20:40:38 PDT 2013
[  1306.139] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[  1306.154] (--) using VT number 7

[  1306.155] (II) Loading sub module "fb"
[  1306.155] (II) LoadModule: "fb"
[  1306.156] (II) Loading /usr/lib/xorg/modules/libfb.so
[  1306.156] (II) Module fb: vendor="X.Org Foundation"
[  1306.156]     compiled for 1.14.3, module version = 1.0.0
[  1306.156]     ABI class: X.Org ANSI C Emulation, version 0.4
[  1306.156] (II) Loading sub module "wfb"
[  1306.156] (II) LoadModule: "wfb"
[  1306.156] (II) Loading /usr/lib/xorg/modules/libwfb.so
[  1306.166] (II) Module wfb: vendor="X.Org Foundation"
[  1306.166]     compiled for 1.14.3, module version = 1.0.0
[  1306.166]     ABI class: X.Org ANSI C Emulation, version 0.4
[  1306.166] (II) Loading sub module "ramdac"
[  1306.166] (II) LoadModule: "ramdac"
[  1306.166] (II) Module "ramdac" already built-in
[  1306.182] (II) NVIDIA(0): Creating default Display subsection in Screen section
    "Default Screen Section" for depth/fbbpp 24/32
[  1306.182] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
[  1306.182] (==) NVIDIA(0): RGB weight 888
[  1306.182] (==) NVIDIA(0): Default visual is TrueColor
[  1306.182] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[  1306.182] (**) NVIDIA(0): Option "NoLogo" "true"
[  1306.182] (**) NVIDIA(0): Option "ProbeAllGpus" "false"
[  1306.182] (**) NVIDIA(0): Option "UseEDID" "false"
[  1306.182] (**) NVIDIA(0): Option "UseDisplayDevice" "none"
[  1306.183] (**) NVIDIA(0): Enabling 2D acceleration
[  1306.183] (**) NVIDIA(0): Ignoring EDIDs
[  1306.183] (**) NVIDIA(0): Option "UseDisplayDevice" set to "none"; enabling NoScanout
[  1306.183] (**) NVIDIA(0):     mode
[  1306.198] (EE) NVIDIA(0): Failed to initialize the NVIDIA kernel module. Please see the
[  1306.198] (EE) NVIDIA(0):     system's kernel log for additional error messages and
[  1306.198] (EE) NVIDIA(0):     consult the NVIDIA README for details.
[  1306.198] (EE) NVIDIA(0):  *** Aborting ***
[  1306.198] (EE) NVIDIA(0): Failing initialization of X screen 0
[  1306.198] (II) UnloadModule: "nvidia"
[  1306.198] (II) UnloadSubModule: "wfb"
[  1306.198] (II) UnloadSubModule: "fb"
[  1306.198] (EE) Screen(s) found, but none have a usable configuration.
[  1306.198] (EE) 
Fatal server error:
[  1306.198] (EE) no screens found(EE) 
[  1306.198] (EE) 
Please consult the The X.Org Foundation support 
     at http://wiki.x.org
 for help. 
[  1306.198] (EE) Please also check the log file at "/var/log/Xorg.8.log" for additional information.
[  1306.198] (EE) 
[  1306.198] (EE) Server terminated with error (1). Closing log file.

Dodam że Komputer to laptop Lenovo IdeaPad Z500 z Debianem jessie na pokładzie.
Z góry dzięki za wszelką pomoc, pozdrawiam :)

morfik · 2013-11-26 22:19:59

Na pewno masz odpowiednie pakiety od nvidii zainstalowane? Weź sobie doinstaluj pakiet

Kod:

nvidia-detect

I zobacz co pokaże, Np w moim przypadku:

Kod:

# nvidia-detect
Detected NVIDIA GPUs:
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation G73 [GeForce 7600 GT] [10de:0391] (rev a1)
Your card is only supported up to the 304 legacy drivers series.
It is recommended to install the
    nvidia-legacy-304xx-driver
package.

fervi · 2013-11-26 22:20:14

W bumblebee.conf zmień 55 linijkę
Teraz wygląda tak:

Kod:

KernelDriver=nvidia

A ma wyglądać:

Kod:

KernelDriver=nvidia-current

Zazwyczaj pomaga :D

Fervi

Miziak · 2013-11-26 23:04:49

Więc tak wywaliłem wszystko co w nazwie ma nvidia i zainstalowałem ster polecany przez nvidia-detect.
@fervi
tak mam w configu ale odkryłem nowy problem:

Kod:

miziak@debian:~$ cat /proc/acpi/bbswitch
0000:01:00.0 OFF

i za żadne skarby po poleceniu:

Kod:

miziak@debian:~$ sudo tee /proc/acpi/bbswitch <<<ON

nie wstaje przy próbie uruchomienia czegoś dostaję:

Kod:

miziak@debian:~$ optirun glxgears
[ 1526.660346] [ERROR]Cannot access secondary GPU - error: Could not enable discrete graphics card

[ 1526.660456] [ERROR]Aborting because fallback start is disabled.

uzytkownikubunt · 2013-11-26 23:25:09

278

Ostatnio edytowany przez uzytkownikubunt (2016-12-01 00:41:18)

fervi · 2013-11-26 23:25:58

Jeśli miałeś nvidia-current to na nvidię trzeba było zmienić :P

Kod:

dpkg --list | grep nvidia
lspci | grep VGA

Fervi

Ostatnio edytowany przez fervi (2013-11-26 23:26:46)

Miziak · 2013-11-26 23:36:16

Znaczy sam zmieniałem na nvidia-current :)

Kod:

miziak@debian:~$ dpkg --list | grep nvidia
ii  bumblebee-nvidia                      3.2.1-4                         amd64        NVIDIA Optimus support using the proprietary NVIDIA driver
ii  glx-alternative-nvidia                0.4.1                           amd64        allows the selection of NVIDIA as GLX provider
ii  libgl1-nvidia-glx:amd64               319.72-1                        amd64        NVIDIA binary OpenGL libraries
ii  libgl1-nvidia-glx:i386                319.72-1                        i386         NVIDIA binary OpenGL libraries
ii  libgl1-nvidia-glx-i386                319.72-1                        i386         NVIDIA binary OpenGL 32-bit libraries
ii  libnvidia-ml1:amd64                   319.72-1                        amd64        NVIDIA Management Library (NVML) runtime library
ii  nvidia-alternative                    319.72-1                        amd64        allows the selection of NVIDIA as GLX provider
ii  nvidia-detect                         319.72-1                        amd64        NVIDIA GPU detection utility
ii  nvidia-driver                         319.72-1                        amd64        NVIDIA metapackage
ii  nvidia-installer-cleanup              20131102+1                      amd64        cleanup after driver installation with the nvidia-installer
ii  nvidia-kernel-common                  20131102+1                      amd64        NVIDIA binary kernel module support files
ii  nvidia-kernel-dkms                    319.72-1                        amd64        NVIDIA binary kernel module DKMS source
ii  nvidia-settings                       319.72-1                        amd64        tool for configuring the NVIDIA graphics driver
ii  nvidia-support                        20131102+1                      amd64        NVIDIA binary graphics driver support files
ii  nvidia-vdpau-driver:amd64             319.72-1                        amd64        NVIDIA vdpau driver
ii  xserver-xorg-video-nvidia             319.72-1                        amd64        NVIDIA binary Xorg driver

Kod:

miziak@debian:~$ lspci | grep VGA
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
01:00.0 VGA compatible controller: NVIDIA Corporation GK107M [GeForce GT 645M] (rev ff)

@uzytkownikubunt
Kernel 3.9 mam.

fervi · 2013-11-26 23:39:57

Kod:

optirun --debug echo "Fervi jest fajny"

Fervi

PS. Co ci się zaktualizowało?

Ostatnio edytowany przez fervi (2013-11-26 23:43:31)

Miziak · 2013-11-26 23:48:50

Kod:

miziak@debian:~$ optirun --debug echo "Fervi jest fajny"
[  240.828694] [DEBUG]optirun version 3.2.1 starting...
[  240.828732] [DEBUG]Active configuration:
[  240.828742] [DEBUG] bumblebeed config file: /etc/bumblebee/bumblebee.conf
[  240.828765] [DEBUG] X display: :8
[  240.828783] [DEBUG] LD_LIBRARY_PATH: /usr/lib/x86_64-linux-gnu/nvidia:/usr/lib/i386-linux-gnu/nvidia:/usr/lib/nvidia
[  240.828796] [DEBUG] Socket path: /var/run/bumblebee.socket
[  240.828804] [DEBUG] Accel/display bridge: auto
[  240.828814] [DEBUG] VGL Compression: proxy
[  240.828826] [DEBUG] VGLrun extra options: 
[  240.828837] [DEBUG] Primus LD Path: /usr/lib/x86_64-linux-gnu/primus:/usr/lib/i386-linux-gnu/primus:/usr/lib/primus:/usr/lib32/primus
[  240.828873] [DEBUG]Using auto-detected bridge primus
[  240.829035] [INFO]Response: No - error: [XORG] (EE) NVIDIA(0): Failed to initialize the NVIDIA GPU at PCI:1:0:0.  Please

[  240.829054] [ERROR]Cannot access secondary GPU - error: [XORG] (EE) NVIDIA(0): Failed to initialize the NVIDIA GPU at PCI:1:0:0.  Please

[  240.829072] [DEBUG]Socket closed.
[  240.829090] [ERROR]Aborting because fallback start is disabled.
[  240.829107] [DEBUG]Killing all remaining processes.

Generalnie to cały system bo dość długo go nie aktualizowałem.
No tak mi ta aktualizacja krwi napsuła przez tego Optimusa...

Ostatnio edytowany przez Miziak (2013-11-26 23:50:47)

fervi · 2013-11-26 23:54:22

Kod:

[  240.829035] [INFO]Response: No - error: [XORG] (EE) NVIDIA(0): Failed to initialize the NVIDIA GPU at PCI:1:0:0.  Please

To wszystko co wyświetla?
Ogólnie jeśli się nie mylę musisz zamienić z nvidia-current na nvidia :P

Jedyne co przychodzi mi do głowy ...

Kod:

LibraryPath=/usr/lib/x86_64-linux-gnu/nvidia:/usr/lib/i386-linux-gnu/nvidia:/usr/lib/nvidia

Sprawdź czy masz takie katalogi

Fervi

Miziak · 2013-11-27 00:05:15

Tak, tylko to.
Generalnie bbswitch cały czas jest OFF i za cholerę nie chce wstawać a wczoraj jeszcze działał nie wiem chyba zabiłem sobie grafę(mam nadzieję, że tylko dla systemu).
Wszystkie katalogi istnieją i zawierają pliki.

Jeszcze przy włączaniu komputera zauważyłem, że acpi-handle-hack krzyczy o braku jakiegoś urządzenia i wygląda to dość dziwnie bo próbuje to zrobić kilka razy, za każdym razem z tym samym błędem.

fervi · 2013-11-27 00:13:11

Ja bym proponował przejść na 3.11 ogólnie

Kod:

sudo dkms status
ls /boot

Na dobranoc jeszcze

Fervi

Ostatnio edytowany przez fervi (2013-11-27 00:13:25)

Miziak · 2013-11-27 00:18:25

Znaczy ja mam jądro 3.11 i na nim pracuję :)

Kod:

miziak@debian:~$ sudo dkms status
[sudo] password for miziak: 
acpi-handle-hack, 0.0.2, 3.11-2-amd64, x86_64: installed (WARNING! Diff between built and installed module!)
bbswitch, 0.7, 3.11-2-amd64, x86_64: installed
nvidia-current, 319.72, 3.11-2-amd64, x86_64: installed

Kod:

miziak@debian:~$ ls /boot
config-2.6.32-5-amd64      initrd.img-3.11-2-amd64    vmlinuz-2.6.32-5-amd64
config-3.11-2-amd64        initrd.img-3.9-1-amd64     vmlinuz-3.11-2-amd64
config-3.9-1-amd64         System.map-2.6.32-5-amd64  vmlinuz-3.9-1-amd64
grub                       System.map-3.11-2-amd64
initrd.img-2.6.32-5-amd64  System.map-3.9-1-amd64

fervi · 2013-11-27 00:24:13

To jeszcze na dobranoc :D

zmień tę linijkę na nvidia-current
i uruchom ponownie komputer

I daj znać :P

acpi-handle-hack; ja nie mam (wątpię by było potrzebne), ogólnie problem taki, że masz inszą wersję tego, niż w pliku Diff

Kod:

ls /var/lib/initramfs-tools | sudo xargs -n1 /usr/lib/dkms/dkms_autoinstaller start

Przebuduje ci wszelkie pakiety DKMS (w tym ten acpi-hack) [chyba jako root odpalać]

Fervi

Ostatnio edytowany przez fervi (2013-11-27 00:26:14)

Miziak · 2013-11-27 00:32:17

To tak cała sekwencja pokażę bo niby bbswtch wstaje ale po próbie opalenia czegokolwiek "umiera" i już nie wstanie:

Kod:

miziak@debian:~$ cat /proc/acpi/bbswitch
0000:01:00.0 OFF
miziak@debian:~$ sudo tee /proc/acpi/bbswitch <<<ON
[sudo] password for miziak: 
ON
miziak@debian:~$ cat /proc/acpi/bbswitch
0000:01:00.0 ON
miziak@debian:~$ optirun glxgears
[  184.569081] [ERROR]Cannot access secondary GPU - error: [XORG] (EE) NVIDIA(0): Failed to initialize the NVIDIA GPU at PCI:1:0:0.  Please

[  184.569137] [ERROR]Aborting because fallback start is disabled.
miziak@debian:~$ cat /proc/acpi/bbswitch
0000:01:00.0 OFF

A jak te acpi... wyplenić ;może to to coś miesza.

fervi · 2013-11-27 00:38:04

Kod:

cat /etc/bumblebee/bumblebee.conf

Muszę być pewny wszystkiego :D

Fervi

Miziak · 2013-11-27 00:50:10

Proszę xD

Kod:

miziak@debian:~$ cat /etc/bumblebee/bumblebee.conf
# Configuration file for Bumblebee. Values should **not** be put between quotes

## Server options. Any change made in this section will need a server restart
# to take effect.
[bumblebeed]
# The secondary Xorg server DISPLAY number
VirtualDisplay=:8
# Should the unused Xorg server be kept running? Set this to true if waiting
# for X to be ready is too long and don't need power management at all.
KeepUnusedXServer=false
# The name of the Bumbleblee server group name (GID name)
ServerGroup=bumblebee
# Card power state at exit. Set to false if the card shoud be ON when Bumblebee
# server exits.
TurnCardOffAtExit=false
# The default behavior of '-f' option on optirun. If set to "true", '-f' will
# be ignored.
NoEcoModeOverride=false
# The Driver used by Bumblebee server. If this value is not set (or empty),
# auto-detection is performed. The available drivers are nvidia and nouveau
# (See also the driver-specific sections below)
Driver=
# Directory with a dummy config file to pass as a -configdir to secondary X
XorgConfDir=/etc/bumblebee/xorg.conf.d

## Client options. Will take effect on the next optirun executed.
[optirun]
# Acceleration/ rendering bridge, possible values are auto, virtualgl and
# primus.
Bridge=auto
# The method used for VirtualGL to transport frames between X servers.
# Possible values are proxy, jpeg, rgb, xv and yuv.
VGLTransport=proxy
# List of paths which are searched for the primus libGL.so.1 when using
# the primus bridge
PrimusLibraryPath=/usr/lib/x86_64-linux-gnu/primus:/usr/lib/i386-linux-gnu/primus:/usr/lib/primus:/usr/lib32/primus
# Should the program run under optirun even if Bumblebee server or nvidia card
# is not available?
AllowFallbackToIGC=false

# Driver-specific settings are grouped under [driver-NAME]. The sections are
# parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto-
# detection resolves to NAME).
# PMMethod: method to use for saving power by disabling the nvidia card, valid
# values are: auto - automatically detect which PM method to use
# bbswitch - new in BB 3, recommended if available
# switcheroo - vga_switcheroo method, use at your own risk
# none - disable PM completely
# https://github.com/Bumblebee-Project/Bumblebee/wiki/Comparison-of-PM-methods

## Section with nvidia driver specific options, only parsed if Driver=nvidia
[driver-nvidia]
# Module name to load, defaults to Driver if empty or unset
KernelDriver=nvidia-current
PMMethod=auto
# colon-separated path to the nvidia libraries
LibraryPath=/usr/lib/x86_64-linux-gnu/nvidia:/usr/lib/i386-linux-gnu/nvidia:/usr/lib/nvidia
# comma-separated path of the directory containing nvidia_drv.so and the
# default Xorg modules path
XorgModulePath=/usr/lib/nvidia,/usr/lib/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia

## Section with nouveau driver specific options, only parsed if Driver=nouveau
[driver-nouveau]
KernelDriver=nouveau
PMMethod=auto
XorgConfFile=/etc/bumblebee/xorg.conf.nouveau

fervi · 2013-11-27 00:56:25

Kod:

dpkg --list | grep dkms

Spróbuj odpalić na kernelu 3.9 i daj znać czy działa

Ja o 7:30-8:00 sprawdzę co tu wymodziłeś

Fervi

PS. Co zwraca

Kod:

sudo modprobe nvidia
sudo modprobe nvidia-current

Ostatnio edytowany przez fervi (2013-11-27 00:57:38)

miszasty93 · 2013-11-27 01:08:08

Ja nvidie wyłączałem wg. tutka na stronie crunchbanga, możesz też zerknąć na kernel 3.12 który wyłącza kartę (własciwie potrafi ją też włączyć jeśli jest taka potrzeba) na sterownikach otwartych.

fervi · 2013-11-27 07:47:39

Można też użyć zawsze nvidia-prime, ale nie wiem gdzie tego szukać w Debianie ;P

https://github.com/Bumblebee-Project/Bumblebee/issues
Tu możesz zgłosić swój problem

Fervi

Miziak · 2013-11-27 11:09:58

Kod:

miziak@debian:~$ dpkg --list | grep dkms
ii  bbswitch-dkms                         0.7-2                           amd64        Interface for toggling the power on nVidia Optimus video cards
ii  dkms                                  2.2.0.3-1.2                     all          Dynamic Kernel Module Support Framework
ii  nvidia-kernel-dkms                    319.72-1                        amd64        NVIDIA binary kernel module DKMS source

Kod:

miziak@debian:~$ sudo modprobe nvidia
[sudo] password for miziak: 
miziak@debian:~$ sudo modprobe nvidia-current
ERROR: could not insert 'nvidia_current': No such device

Na jądrze 3.9 niby działa ale śmieszne jest to że tam wcale nie ma bbswitch ale działa optirun ale ma niskie fps czyli pewnie śmiga na intelu.

sypu · 2013-11-27 14:33:18

Czytam z zainteresowaniem ten wątek bo sam na świeżo kupionym laptopie próbuję uruchomić wsparcie dla nvidii. Instalowałem bumblee według wiki https://wiki.debian.org/Bumblebee dla architektury 64bit. Jak na razie próba odpalenia optirun konczy sie tak:

Kod:

optirun glxgears
[ 8292.711015] [ERROR]Cannot access secondary GPU - error: Could not load GPU driver

[ 8292.711067] [ERROR]Aborting because fallback start is disabled.

Po wykonaniu
modprobe nvidia
modprobe nvidia-current

Kod:

 optirun glxgears
304 frames in 5.0 seconds = 60.797 FPS
300 frames in 5.0 seconds = 59.984 FPS
300 frames in 5.0 seconds = 59.994 FPS

Kod:

 glxgears
Running synchronized to the vertical refresh.  The framerate should be
approximately the same as the monitor refresh rate.
303 frames in 5.0 seconds = 60.418 FPS
300 frames in 5.0 seconds = 59.989 FPS
300 frames in 5.0 seconds = 59.990 FPS

I nie wiem jak zmusić nvidie do pracy.

Kod:

uname -a
Linux kajko-kokosz 3.11-2-amd64 #1 SMP Debian 3.11.8-1 (2013-11-13) x86_64 GNU/Linux

Kod:

lspci | grep VGA
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)

- czemu tu nie widać karty nvidii?

Kod:

lspci -k
00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09)
    Subsystem: ASUSTeK Computer Inc. Device 124d
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09)
    Kernel driver in use: pcieport
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
    Subsystem: ASUSTeK Computer Inc. Device 124d
    Kernel driver in use: i915
00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04)
    Subsystem: ASUSTeK Computer Inc. Device 124d
    Kernel driver in use: xhci_hcd
00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
    Subsystem: ASUSTeK Computer Inc. Device 124d
    Kernel driver in use: mei_me
00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
    Subsystem: ASUSTeK Computer Inc. Device 124d
    Kernel driver in use: ehci-pci
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
    Subsystem: ASUSTeK Computer Inc. Device 124d
    Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4)
    Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4)
    Kernel driver in use: pcieport
00:1c.3 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 4 (rev c4)
    Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
    Subsystem: ASUSTeK Computer Inc. Device 124d
    Kernel driver in use: ehci-pci
00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04)
    Subsystem: ASUSTeK Computer Inc. Device 124d
    Kernel driver in use: lpc_ich
00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
    Subsystem: ASUSTeK Computer Inc. Device 124d
    Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)
    Subsystem: ASUSTeK Computer Inc. Device 124d
01:00.0 3D controller: NVIDIA Corporation GF117M [GeForce 610M/710M / GT 620M/625M/630M/720M] (rev ff)
03:00.0 Network controller: Qualcomm Atheros AR9485 Wireless Network Adapter (rev 01)
    Subsystem: AzureWave Device 2c97
    Kernel driver in use: ath9k
04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5289 (rev 01)
    Subsystem: ASUSTeK Computer Inc. Device 202f
    Kernel driver in use: rtsx_pci
04:00.2 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0a)
    Subsystem: ASUSTeK Computer Inc. Device 200f
    Kernel driver in use: r8169

i jeszcze config trzmiela

Kod:

cat /etc/bumblebee/bumblebee.conf
# Configuration file for Bumblebee. Values should **not** be put between quotes

## Server options. Any change made in this section will need a server restart
# to take effect.
[bumblebeed]
# The secondary Xorg server DISPLAY number
VirtualDisplay=:8
# Should the unused Xorg server be kept running? Set this to true if waiting
# for X to be ready is too long and don't need power management at all.
KeepUnusedXServer=false
# The name of the Bumbleblee server group name (GID name)
ServerGroup=bumblebee
# Card power state at exit. Set to false if the card shoud be ON when Bumblebee
# server exits.
TurnCardOffAtExit=false
# The default behavior of '-f' option on optirun. If set to "true", '-f' will
# be ignored.
NoEcoModeOverride=false
# The Driver used by Bumblebee server. If this value is not set (or empty),
# auto-detection is performed. The available drivers are nvidia and nouveau
# (See also the driver-specific sections below)
Driver=
# Directory with a dummy config file to pass as a -configdir to secondary X
XorgConfDir=/etc/bumblebee/xorg.conf.d

## Client options. Will take effect on the next optirun executed.
[optirun]
# Acceleration/ rendering bridge, possible values are auto, virtualgl and
# primus.
Bridge=auto
# The method used for VirtualGL to transport frames between X servers.
# Possible values are proxy, jpeg, rgb, xv and yuv.
VGLTransport=proxy
# List of paths which are searched for the primus libGL.so.1 when using
# the primus bridge
PrimusLibraryPath=/usr/lib/x86_64-linux-gnu/primus:/usr/lib/i386-linux-gnu/primus:/usr/lib/primus:/usr/lib32/primus
# Should the program run under optirun even if Bumblebee server or nvidia card
# is not available?
AllowFallbackToIGC=false

# Driver-specific settings are grouped under [driver-NAME]. The sections are
# parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto-
# detection resolves to NAME).
# PMMethod: method to use for saving power by disabling the nvidia card, valid
# values are: auto - automatically detect which PM method to use
# bbswitch - new in BB 3, recommended if available
# switcheroo - vga_switcheroo method, use at your own risk
# none - disable PM completely
# https://github.com/Bumblebee-Project/Bumblebee/wiki/Comparison-of-PM-methods

## Section with nvidia driver specific options, only parsed if Driver=nvidia
[driver-nvidia]
# Module name to load, defaults to Driver if empty or unset
KernelDriver=nvidia-current
PMMethod=auto
# colon-separated path to the nvidia libraries
LibraryPath=/usr/lib/x86_64-linux-gnu/nvidia:/usr/lib/i386-linux-gnu/nvidia:/usr/lib/nvidia
# comma-separated path of the directory containing nvidia_drv.so and the
# default Xorg modules path
XorgModulePath=/usr/lib/nvidia,/usr/lib/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia

## Section with nouveau driver specific options, only parsed if Driver=nouveau
[driver-nouveau]
KernelDriver=nouveau
PMMethod=auto
XorgConfFile=/etc/bumblebee/xorg.conf.nouveau

Będę wdzięczny za pomoc.

wojtos93 · 2014-01-04 19:04:53

Witam wszystkich z okazji mojego pierwszego posta na tym forum. @sypu spróbuj dopisać do Driver= "nvidia".
U mnie występuje podobny problem jak u kolegi sypu na początku.
optirun glxgears zwraca:

Kod:

[ 1224.692309] [ERROR]Cannot access secondary GPU - error: Could not enable discrete graphics card

debian testing + sterownik nvidia 331.20 z repozytoriów experimental + kernel 3.12-1 z unstable

bumblebee.conf:

Kod:

# Configuration file for Bumblebee. Values should **not** be put between quotes

## Server options. Any change made in this section will need a server restart
# to take effect.
[bumblebeed]
# The secondary Xorg server DISPLAY number
VirtualDisplay=:8
# Should the unused Xorg server be kept running? Set this to true if waiting
# for X to be ready is too long and don't need power management at all.
KeepUnusedXServer=false
# The name of the Bumbleblee server group name (GID name)
ServerGroup=bumblebee
# Card power state at exit. Set to false if the card shoud be ON when Bumblebee
# server exits.
TurnCardOffAtExit=false
# The default behavior of '-f' option on optirun. If set to "true", '-f' will
# be ignored.
NoEcoModeOverride=false
# The Driver used by Bumblebee server. If this value is not set (or empty),
# auto-detection is performed. The available drivers are nvidia and nouveau
# (See also the driver-specific sections below)
Driver=nvidia
# Directory with a dummy config file to pass as a -configdir to secondary X
XorgConfDir=/etc/bumblebee/xorg.conf.d

## Client options. Will take effect on the next optirun executed.
[optirun]
# Acceleration/ rendering bridge, possible values are auto, virtualgl and
# primus.
Bridge=auto
# The method used for VirtualGL to transport frames between X servers.
# Possible values are proxy, jpeg, rgb, xv and yuv.
VGLTransport=proxy
# List of paths which are searched for the primus libGL.so.1 when using
# the primus bridge
PrimusLibraryPath=/usr/lib/x86_64-linux-gnu/primus:/usr/lib/i386-linux-gnu/primus:/usr/lib/primus:/usr/lib32/primus
# Should the program run under optirun even if Bumblebee server or nvidia card
# is not available?
AllowFallbackToIGC=false

# Driver-specific settings are grouped under [driver-NAME]. The sections are
# parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto-
# detection resolves to NAME).
# PMMethod: method to use for saving power by disabling the nvidia card, valid
# values are: auto - automatically detect which PM method to use
# bbswitch - new in BB 3, recommended if available
# switcheroo - vga_switcheroo method, use at your own risk
# none - disable PM completely
# https://github.com/Bumblebee-Project/Bumblebee/wiki/Comparison-of-PM-methods

## Section with nvidia driver specific options, only parsed if Driver=nvidia
[driver-nvidia]
# Module name to load, defaults to Driver if empty or unset
KernelDriver=nvidia-current
PMMethod=auto
# colon-separated path to the nvidia libraries
LibraryPath=/usr/lib/x86_64-linux-gnu/nvidia:/usr/lib/i386-linux-gnu/nvidia:/usr/lib/nvidia
# comma-separated path of the directory containing nvidia_drv.so and the
# default Xorg modules path
XorgModulePath=/usr/lib/nvidia,/usr/lib/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia

## Section with nouveau driver specific options, only parsed if Driver=nouveau
[driver-nouveau]
KernelDriver=nouveau
PMMethod=auto
XorgConfFile=/etc/bumblebee/xorg.conf.nouveau

xorg.conf.nvidia:

Kod:

Section "ServerLayout"
    Identifier "Layout0"
    Option "AutoAddDevices" "false"
    EndSection

    Section "Device"
    Identifier "Device1"
    Driver "nvidia"
    VendorName "NVIDIA Corporation"
    BusID "PCI:1:0:0"
    Option "NoLogo" "true"
    Option "UseEDID" "false"
    Option "ConnectedMonitor" "DFP"
    Option "UseDisplayDevice" "none"
    EndSection

Forum Debian Users Gang

Ogłoszenie

#1 2013-11-26 21:53:38

Miziak - Użytkownik

Nvidia Optimus problem po aktualizacji.

Kod:

Kod:

Kod:

Kod:

Kod:

Kod:

#2 2013-11-26 22:19:59

morfik - Cenzor wirtualnego świata

Re: Nvidia Optimus problem po aktualizacji.

Kod:

Kod:

#3 2013-11-26 22:20:14

fervi - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

Kod:

#4 2013-11-26 23:04:49

Miziak - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

Kod:

Kod:

#5 2013-11-26 23:25:09

uzytkownikubunt - Zbanowany

Re: Nvidia Optimus problem po aktualizacji.

#6 2013-11-26 23:25:58

fervi - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

#7 2013-11-26 23:36:16

Miziak - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

Kod:

#8 2013-11-26 23:39:57

fervi - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

#9 2013-11-26 23:48:50

Miziak - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

#10 2013-11-26 23:54:22

fervi - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

Kod:

#11 2013-11-27 00:05:15

Miziak - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

#12 2013-11-27 00:13:11

fervi - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

#13 2013-11-27 00:18:25

Miziak - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

Kod:

#14 2013-11-27 00:24:13

fervi - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

#15 2013-11-27 00:32:17

Miziak - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

#16 2013-11-27 00:38:04

fervi - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod:

#17 2013-11-27 00:50:10

Miziak - Użytkownik

Re: Nvidia Optimus problem po aktualizacji.

Kod: