Forum Debian Users Gang

ifconfig ath0 up
ath0: ERROR while getting interface flags: Nie ma takiego urządzenia

 iwlist scan
lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

eth1      Interface doesn't support scanning.

wifi0     Interface doesn't support scanning.

wlan0     No scan results
sit0      Interface doesn't support scanning.

TCP reno registered
audit: initializing netlink socket (disabled)
audit(1212345151.600:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
0000:00:10.4 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
PCI: Bypassing VIA 8237 APIC De-Assert Message
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI: (supports<6>Time: tsc clocksource has been installed.
 S0 S1 S4 S5)
Freeing unused kernel memory: 196k freed
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Thermal Zone [THRM] (40 C)
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 18 (level, low) -> IRQ 169
eth0: RTL8169sc/8110sc at 0xf881c000, 00:30:18:aa:5f:f1, IRQ 169
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 177
eth1: RTL8169sc/8110sc at 0xf881e000, 00:30:18:aa:5f:f2, IRQ 177
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 185
PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 9
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0xfa00-0xfa07, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
libata version 2.00 loaded.
Time: acpi_pm clocksource has been installed.
hda: SAMSUNG SP0411N, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 193
PCI: VIA IRQ fixup for 0000:00:10.0, from 11 to 1
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 193, io base 0x0000f900
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 193
PCI: VIA IRQ fixup for 0000:00:10.1, from 11 to 1
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 193, io base 0x0000f800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[b] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 193
PCI: VIA IRQ fixup for 0000:00:10.2, from 11 to 1
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 193, io base 0x0000f700
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[b] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 193
PCI: VIA IRQ fixup for 0000:00:10.3, from 11 to 1
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 193, io base 0x0000f600
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 193
PCI: VIA IRQ fixup for 0000:00:10.4, from 5 to 1
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 193, io mem 0xfdffd000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
sata_via 0000:00:0f.0: version 2.0
ACPI: PCI Interrupt 0000:00:0f.0[b] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 185
sata_via 0000:00:0f.0: routed to hard irq line 11
ata1: SATA max UDMA/133 cmd 0xFF00 ctl 0xFE02 bmdma 0xFB00 irq 185
ata2: SATA max UDMA/133 cmd 0xFD00 ctl 0xFC02 bmdma 0xFB08 irq 185
scsi0 : sata_via
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/1)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : sata_via
ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0xFD07
  Vendor: ATA       Model: WDC WD3200YS-01P  Rev: 21.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
hda: max request size: 512KiB
hda: 78242976 sectors (40060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(33)
hda: cache flushes supported
 hda:<5>SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
 hda1 hda2 <<5>sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
 hda5<5>sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1
sd 0:0:0:0: Attached scsi disk sda
 hda6 hda7 hda8 hda9 hda10 hda11 >
Probing IDE interface ide1...
Attempting manual resume
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA P4M800CE chipset
agpgart: AGP aperture is 128M @ 0xe8000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.10.2.2-ATHEROS (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425)
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
wlan: 0.8.4.2 (svn r2756)
ath_pci: 0.9.4.5 (svn r2756)
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 17 (level, low) -> IRQ 201
ath_pci: switching rfkill capability off
ath_rate_sample: 1.2 (svn r2756)
ath_pci: switching per-packet transmit power control off
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 7.8 phy 4.5 radio 5.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 2413: mem=0xfdfe0000, irq=201
Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 209
via82cxxx: Six channel audio available
PCI: Setting latency timer of device 0000:00:11.5 to 64
ac97_codec: AC97  codec, id: ALG96 (Unknown)
via82cxxx: Codec rate locked at 48Khz
via82cxxx: board #1 at 0xEE00, IRQ 209
input: PC Speaker as /class/input/input0
Real Time Clock Driver v1.12ac
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Adding 2650684k swap on /dev/hda7.  Priority:-1 extents:1 across:2650684k
EXT3 FS on hda1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda11, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
r8169: eth0: link up
r8169: eth1: link down
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth1: link is not ready
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
wlan0: no IPv6 routers present

Module                  Size  Used by
lm80                   15696  0
ipv6                  226272  24
button                  6672  0
ac                      5188  0
battery                 9636  0
dm_snapshot            15552  0
dm_mirror              19152  0
dm_mod                 50232  2 dm_snapshot,dm_mirror
loop                   15048  0
evdev                   9088  0
parport_pc             32132  0
parport                33256  1 parport_pc
rtc                    12372  0
psmouse                35016  0
snd_via82xx            26008  0
gameport               14632  1 snd_via82xx
snd_ac97_codec         83104  1 snd_via82xx
snd_ac97_bus            2400  1 snd_ac97_codec
snd_pcm                68676  2 snd_via82xx,snd_ac97_codec
snd_timer              20996  1 snd_pcm
snd_page_alloc         10184  2 snd_via82xx,snd_pcm
snd_mpu401_uart         8064  1 snd_via82xx
snd_rawmidi            22560  1 snd_mpu401_uart
snd_seq_device          7820  1 snd_rawmidi
snd                    47012  7 snd_via82xx,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
i2c_viapro              8244  0
serio_raw               6660  0
pcspkr                  3072  0
via82cxxx_audio        24232  0
uart401                11172  1 via82cxxx_audio
sound                  69768  2 via82cxxx_audio,uart401
soundcore               9248  3 snd,via82cxxx_audio,sound
ac97_codec             17196  1 via82cxxx_audio
wlan_scan_sta          12160  1
i2c_core               19680  2 lm80,i2c_viapro
ath_rate_sample        12288  1
ath_pci                98696  0
wlan                  182224  4 wlan_scan_sta,ath_rate_sample,ath_pci
shpchp                 33024  0
ath_hal               279328  3 ath_rate_sample,ath_pci
pci_hotplug            28704  1 shpchp
via_agp                 9664  1
agpgart                29896  1 via_agp
ext3                  119240  8
jbd                    52456  1 ext3
mbcache                 8356  1 ext3
ide_generic             1408  0 [permanent]
sd_mod                 19040  2
ide_disk               14848  9
generic                 4868  0 [permanent]
sata_via               10052  2
ehci_hcd               28136  0
libata                 89396  1 sata_via
scsi_mod              124168  2 sd_mod,libata
uhci_hcd               21164  0
usbcore               112644  3 ehci_hcd,uhci_hcd
via82cxxx               8388  0 [permanent]
ide_core              110504  4 ide_generic,ide_disk,generic,via82cxxx
r8169                  28360  0
thermal                13608  0
processor              28840  1 thermal
fan                     4804  0