Nie jesteś zalogowany.
Jeśli nie posiadasz konta, zarejestruj je już teraz! Pozwoli Ci ono w pełni korzystać z naszego serwisu. Spamerom dziękujemy!

Ogłoszenie

Prosimy o pomoc dla małej Julki — przekaż 1% podatku na Fundacji Dzieciom zdazyć z Pomocą.
Więcej informacji na dug.net.pl/pomagamy/.

Strony: 1

 

#1  2007-04-08 17:56:51

  AdamP - Użytkownik

AdamP
Użytkownik
Skąd: Warszawa
Zarejestrowany: 2005-10-30
Serwis

kontroler SATA i nie widzi ATA

Witam
mam kontroler SATA na PCI i podłączony do niego dysk 250Gb Samsunga i na nim Debiana.
W czasie instalacji instalator widział dwa dyski 18Gb IBM'a na ATA100 i 250Gb na SATA.
A teraz nawet CD nie widzi na ATA.
Co jest grane? Co mam zrobić aby znów mieć dostęp do CD - dokładnie nagrywarki CD-RW i drugiego dysku na małe backupy?
P.S. Dlaczego on widzi SATA jako SCSI?

Offline

 

#2  2007-04-08 18:00:49

  zimzum - Członek DUG

zimzum
Członek DUG
Zarejestrowany: 2006-09-04

Re: kontroler SATA i nie widzi ATA

Co Ci wypluwa

Kod:

fdisk -l

? Dyski SATA sa wykrywane jako sda, sdb (czyli tak jak SCSI), a nie ja zwykle ATA, czyli hda, hdb.

Offline

 

#3  2007-04-08 18:03:12

  AdamP - Użytkownik

AdamP
Użytkownik
Skąd: Warszawa
Zarejestrowany: 2005-10-30
Serwis

Re: kontroler SATA i nie widzi ATA

Kod:

# fdisk -l

Disk /dev/sda: 250.0 GB, 250059350016 bytes
255 heads, 63 sectors/track, 30401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *           1       30209   242653761   83  Linux
/dev/sda2           30210       30401     1542240    5  Extended
/dev/sda5           30210       30401     1542208+  82  Linux swap / Solaris

Kod:

# lspci
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge
0000:00:09.0 Communication controller: Motorola: Unknown device 5608
0000:00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
0000:00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
0000:00:0c.0 RAID bus controller: Silicon Image, Inc. (formerly CMD Technology Inc) SiI 3512 [SATALink/SATARaid] Serial ATA Controller (rev 01)
0000:00:0d.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
0000:00:0d.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
0000:00:0e.0 Multimedia audio controller: Quicknet Technologies Inc: Unknown device 0500
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:14.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
0000:01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2)

Offline

 

#4  2007-04-09 19:42:15

  AdamP - Użytkownik

AdamP
Użytkownik
Skąd: Warszawa
Zarejestrowany: 2005-10-30
Serwis

Re: kontroler SATA i nie widzi ATA

czy ktoś wie co jest nie tak ?

Offline

 

#5  2007-04-09 20:23:49

  qluk - Pan inż. Cyc

qluk
Pan inż. Cyc
Skąd: Katowice
Zarejestrowany: 2006-05-22

Re: kontroler SATA i nie widzi ATA

A obluge masz przez PATA/SATA czy tradycyjne ATA? No i podaj log z rozruchu.

Offline

 

#6  2007-04-09 20:30:29

  AdamP - Użytkownik

AdamP
Użytkownik
Skąd: Warszawa
Zarejestrowany: 2005-10-30
Serwis

Re: kontroler SATA i nie widzi ATA

Kod:

Linux version 2.6.8-2-686 (horms@tabatha.lab.ultramonkey.org) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Tue Aug 16 13:22:48 UTC 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
 BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
 BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131056
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 126960 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 KT400                                     ) @ 0x000f6b80
ACPI: RSDT (v001 KT400  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 KT400  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: DSDT (v001 KT400  AWRDACPI 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Built 1 zonelists
Kernel command line: root=/dev/sda1 ro
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 800.162 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 511340k/524224k available (1551k kernel code, 12104k reserved, 690k data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1581.05 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: After vendor identify, caps:  0183fbff c1c7fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After all inits, caps:        0183fbff c1c7fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Duron(tm) processor stepping 00
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 799.0923 MHz.
..... host bus clock speed is 199.0980 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4528k freed
NET: Registered protocol family 16
spurious 8259A interrupt: IRQ7.
PCI: PCI BIOS revision 2.10 entry at 0xfb380, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbe60
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbe90, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 12 (level, low) -> IRQ 12
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:0d.1[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:10.1[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 12 (level, low) -> IRQ 12
ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 5 (level, low) -> IRQ 5
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4528 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.02 loaded.
sata_sil version 0.54
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 11 (level, low) -> IRQ 11
ata1: SATA max UDMA/100 cmd 0xE081E080 ctl 0xE081E08A bmdma 0xE081E000 irq 11
ata2: SATA max UDMA/100 cmd 0xE081E0C0 ctl 0xE081E0CA bmdma 0xE081E008 irq 11
ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7468 86:bc01 87:4023 88:40ff
ata1: dev 0 ATA, max UDMA7, 488397168 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: no device found (phy stat 00000000)
scsi1 : sata_sil
Using anticipatory io scheduler
  Vendor: ATA       Model: SAMSUNG SP2504C   Rev: VT10
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
 /dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1542200k swap on /dev/sda5.  Priority:-1 extents:1
EXT3 FS on sda1, internal journal
Generic RTC Driver v1.07
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Capability LSM initialized
irda_init()
NET: Registered protocol family 23
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xa400, 00:50:fc:49:a1:58, IRQ 10
eth0:  Identified 8139 chip type 'RTL-8139C'
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 12 (level, low) -> IRQ 12
eth1: RealTek RTL8139 at 0xa800, 00:50:fc:30:b5:19, IRQ 12
eth1:  Identified 8139 chip type 'RTL-8139C'
cmpci: version $Revision: 6.82 $ time 13:45:27 Aug 16 2005
ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 11 (level, low) -> IRQ 11
cmpci:
cmpci: found CM8738 adapter at io 0xe000 irq 11
cmpci: chip version = 055
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: irq 5, io base 0000c800
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[B] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: irq 10, io base 0000cc00
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: irq 12, io base 0000d000
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.3: irq 11, pci mem e0885000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 128M @ 0xd0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 5 (level, low) -> IRQ 5
bttv0: Bt878 (rev 17) at 0000:00:0d.0, irq: 5, latency: 32, mmio: 0xe2084000
bttv0: using:  *** UNKNOWN/GENERIC ***  [card=0,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv: readee error
bttv0: using tuner=-1
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: registered device video0
bttv0: registered device vbi0
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI interrupt 0000:00:0d.1[A] -> GSI 5 (level, low) -> IRQ 5
bt878(0): Bt878 (rev 17) at 00:0d.1, irq: 5, latency: 32, memory: 0xe2085000
btaudio: driver version 0.7 loaded [digital+analog]
input: PC Speaker
inserting floppy driver for 2.6.8-2-686
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
eth1: link up, 10Mbps, half-duplex, lpa 0x0000
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0300140(lo)
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
lp0: using parport0 (interrupt-driven).
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 296 bytes per conntrack
eth0: no IPv6 routers present
eth1: no IPv6 routers present

Offline

 

 

Strony: 1

Stopka forum

Powered by PunBB
© Copyright 2002–2005 Rickard Andersson
To nie jest tylko forum, to nasza mała ojczyzna ;-)