Forum Debian Users Gang

[ 2082.002205] p54pci 0000:00:0e.0: PCI INT A disabled
[ 2082.261377] cfg80211: Using static regulatory domain info
[ 2082.330013] cfg80211: Regulatory domain: US
[ 2082.383836]  (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2082.477719]  (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 2082.563003]  (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 2082.648157]  (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 2082.733149]  (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 2082.817924]  (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 2082.902778]  (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 2082.995413] cfg80211: Calling CRDA for country: US
[ 2083.226230] p54pci 0000:00:0e.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
[ 2083.332551] p54pci 0000:00:0e.0: firmware: requesting isl3886pci
[ 2083.431093] phy0: p54 detected a LM86 firmware
[ 2083.488820] p54: rx_mtu reduced from 3240 to 2376
[ 2083.549786] phy0: FW rev 2.13.12.0 - Softmac protocol 5.9
[ 2083.619195] phy0: cryptographic accelerator WEP:YES, TKIP:YES, CCMP:YES
[ 2084.555723] phy0: [curve data] is/are missing for channel:2 [2417 MHz].
[ 2084.640205] phy0: [curve data] is/are missing for channel:3 [2422 MHz].
[ 2084.724573] phy0: [curve data] is/are missing for channel:4 [2427 MHz].
[ 2084.808726] phy0: [curve data] is/are missing for channel:5 [2432 MHz].
[ 2084.892775] phy0: [curve data] is/are missing for channel:6 [2437 MHz].
[ 2084.976791] phy0: [curve data] is/are missing for channel:7 [2442 MHz].
[ 2085.060827] phy0: [curve data] is/are missing for channel:8 [2447 MHz].
[ 2085.144842] phy0: [curve data] is/are missing for channel:9 [2452 MHz].
[ 2085.228710] phy0: [curve data] is/are missing for channel:10 [2457 MHz].
[ 2085.313550] phy0: [curve data] is/are missing for channel:11 [2462 MHz].
[ 2085.398302] phy0: [curve data] is/are missing for channel:12 [2467 MHz].
[ 2085.482892] phy0: [curve data] is/are missing for channel:13 [2472 MHz].
[ 2085.567374] phy0: [curve data] is/are missing for channel:14 [2484 MHz].
[ 2085.651701] phy0: hwaddr xx:xx:xx:xx:xx:xx, MAC:isl3880 RF:Frisbee
[ 2085.734575] phy0: Selected rate control algorithm 'minstrel'
[ 2085.745246] Registered led device: p54-phy0::assoc
[ 2085.881275] Registered led device: p54-phy0::tx
[ 2085.954739] Registered led device: p54-phy0::rx
[ 2086.014082] Registered led device: p54-phy0::radio
[ 2086.075216] p54pci 0000:00:0e.0: is registered as 'phy0'

iwlist wlan0 channel
wlan0     1 channels in total; available frequencies :
          Channel 01 : 2.412 GHz