Nie jesteś zalogowany.
Jeśli nie posiadasz konta, zarejestruj je już teraz! Pozwoli Ci ono w pełni korzystać z naszego serwisu. Spamerom dziękujemy!

Ogłoszenie

Prosimy o pomoc dla małej Julki — przekaż 1% podatku na Fundacji Dzieciom zdazyć z Pomocą.
Więcej informacji na dug.net.pl/pomagamy/.

#1  2009-05-30 19:09:48

  reinkkrz - Użytkownik

reinkkrz
Użytkownik
Skąd: Nakło nad Notecią
Zarejestrowany: 2009-05-11

kamera AGFA CL18.

Witam.
Mam aparat fot : AGFA CL18.z możliwością Kamerki .

Nie wiem jak ją zainstalować aby działała jako kamera ze skypem pod Linuksem. Pod Windows nie było żadnych problemów z tym, a tutaj naprawdę nie wiem. Dlatego piszę z prośbą o pomoc.
Pozdrawiam.

Kod:

root@siduxbox:/home/krzysztof# lsusb
Bus 002 Device 002: ID 06bd:0403 AGFA-Gevaert NV ePhoto CL18 Camera
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Kod:

root@siduxbox:/home/krzysztof# dmesg
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.29-4.slh.4-sidux-686 (Debian 2.6.29-27) (s.l-h@gmx.de) (gcc version 4.3.3 (Debian 4.3.3-10) ) #1 SMP PREEMPT Thu May 28 01:11:30 UTC 2009
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  NSC Geode by NSC
  Cyrix CyrixInstead
  Centaur CentaurHauls
  Transmeta GenuineTMx86
  Transmeta TransmetaCPU
  UMC UMC UMC UMC
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000017ff0000 (usable)
 BIOS-e820: 0000000017ff0000 - 0000000017ff3000 (ACPI NVS)
 BIOS-e820: 0000000017ff3000 - 0000000018000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
DMI 2.3 present.
last_pfn = 0x17ff0 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
kernel direct mapping tables up to 17ff0000 @ 7000-c000
RAMDISK: 1776c000 - 17fdf909
ACPI: RSDP 000F7790, 0014 (r0 BIOSTA)
ACPI: RSDT 17FF3000, 0028 (r1 BIOSTA AWRDACPI 42302E31 AWRD        0)
ACPI: FACP 17FF3040, 0074 (r1 BIOSTA AWRDACPI 42302E31 AWRD        0)
FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
ACPI: DSDT 17FF30C0, 2571 (r1 VIA694 AWRDACPI     1000 MSFT  100000C)
ACPI: FACS 17FF0000, 0040
0MB HIGHMEM available.
383MB LOWMEM available.
  mapped low ram: 0 - 17ff0000
  low ram: 00000000 - 17ff0000
  bootmap 00002000 - 00005000
(9 early reservations) ==> bootmem [0000000000 - 0017ff0000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0000100000 - 000055b448]    TEXT DATA BSS ==> [0000100000 - 000055b448]
  #4 [001776c000 - 0017fdf909]          RAMDISK ==> [001776c000 - 0017fdf909]
  #5 [000055c000 - 000055f000]    INIT_PG_TABLE ==> [000055c000 - 000055f000]
  #6 [000009fc00 - 0000100000]    BIOS reserved ==> [000009fc00 - 0000100000]
  #7 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
  #8 [0000002000 - 0000005000]          BOOTMAP ==> [0000002000 - 0000005000]
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x00017ff0
  HighMem  0x00017ff0 -> 0x00017ff0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x0000009f
    0: 0x00000100 -> 0x00017ff0
On node 0 totalpages: 98191
free_area_init_node: node 0, pgdat c047ba80, node_mem_map c1000000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 3967 pages, LIFO batch:0
  Normal zone: 736 pages used for memmap
  Normal zone: 93456 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x4008
SMP: Allowing 1 CPUs, 0 hotplug CPUs
Local APIC disabled by BIOS -- you can enable it with "lapic"
nr_irqs_gsi: 16
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 20000000 (gap: 18000000:e7ff0000)
NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
PERCPU: Allocating 36864 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 97423
Kernel command line: root=UUID=4841a23d-74fe-47b7-87fa-720908a9633f ro quiet vga=791
Enabling fast FPU save and restore... done.
Initializing CPU#0
Preemptible RCU implementation.
PID hash table entries: 2048 (order: 11, 8192 bytes)
Fast TSC calibration using PIT
Detected 1320.325 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 375900k/393152k available (2603k kernel code, 16688k reserved, 1041k data, 352k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xffe18000 - 0xfffff000   (1948 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xd87f0000 - 0xff7fe000   ( 624 MB)
    lowmem  : 0xc0000000 - 0xd7ff0000   ( 383 MB)
      .init : 0xc0495000 - 0xc04ed000   ( 352 kB)
      .data : 0xc038ac43 - 0xc048f268   (1041 kB)
      .text : 0xc0100000 - 0xc038ac43   (2603 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency.. 2640.65 BogoMIPS (lpj=1320325)
Security Framework initialized
SELinux:  Disabled at boot.
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Enabling disabled K7/SSE Support.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 10k freed
ACPI: Core revision 20081204
ACPI: Checking initramfs for custom DSDT
ACPI: setting ELCR to 0800 (from 0e20)
weird, boot CPU (#0) not listed by the BIOS.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
SMP disabled
Brought up 1 CPUs
Total of 1 processors activated (2640.65 BogoMIPS).
net_namespace: 1008 bytes
Booting paravirtualized kernel on bare hardware
regulator: core version 0.5
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb380, last bus=1
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: reg 10 32bit mmio: [0xd8000000-0xdbffffff]
pci 0000:00:00.0: Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 81 & 1f -> 01
pci 0000:00:07.1: reg 20 io port: [0xc000-0xc00f]
pci 0000:00:07.2: reg 20 io port: [0xc400-0xc41f]
pci 0000:00:07.3: reg 20 io port: [0xc800-0xc81f]
pci 0000:00:07.4: quirk: region 4000-40ff claimed by vt82c586 ACPI
pci 0000:00:07.4: quirk: region 6000-607f claimed by vt82c686 HW-mon
pci 0000:00:07.4: quirk: region 5000-500f claimed by vt82c686 SMB
pci 0000:00:07.5: reg 10 io port: [0xcc00-0xccff]
pci 0000:00:07.5: reg 14 io port: [0xd000-0xd003]
pci 0000:00:07.5: reg 18 io port: [0xd400-0xd403]
pci 0000:00:09.0: reg 10 io port: [0xdc00-0xdcff]
pci 0000:00:09.0: reg 14 32bit mmio: [0xdf001000-0xdf0010ff]
pci 0000:00:09.0: supports D1 D2
pci 0000:00:09.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:00:09.0: PME# disabled
pci 0000:00:0b.0: reg 10 io port: [0xe000-0xe0ff]
pci 0000:00:0b.0: reg 14 32bit mmio: [0xdf000000-0xdf000fff]
pci 0000:00:0b.0: reg 30 32bit mmio: [0x000000-0x00ffff]
pci 0000:01:00.0: reg 10 32bit mmio: [0xdc000000-0xdcffffff]
pci 0000:01:00.0: reg 14 32bit mmio: [0xd0000000-0xd7ffffff]
pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x00ffff]
pci 0000:00:01.0: bridge 32bit mmio: [0xdc000000-0xddffffff]
pci 0000:00:01.0: bridge 32bit mmio pref: [0xd0000000-0xd7ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
system 00:00: iomem range 0xd0800-0xd3fff has been reserved
system 00:00: iomem range 0xf0000-0xf7fff could not be reserved
system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
system 00:00: iomem range 0xfc000-0xfffff could not be reserved
system 00:00: iomem range 0x17ff0000-0x17ffffff could not be reserved
system 00:00: iomem range 0xffff0000-0xffffffff has been reserved
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0x100000-0x17feffff could not be reserved
system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0:   IO window: disabled
pci 0000:00:01.0:   MEM window: 0xdc000000-0xddffffff
pci 0000:00:01.0:   PREFETCH window: 0x000000d0000000-0x000000d7ffffff
pci 0000:00:01.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 mem: [0x0-0x0]
pci_bus 0000:01: resource 1 mem: [0xdc000000-0xddffffff]
pci_bus 0000:01: resource 2 mem: [0xd0000000-0xd7ffffff]
pci_bus 0000:01: resource 3 mem: [0x0-0x0]
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs...<7>Switched to high resolution mode on CPU 0
 done
Freeing initrd memory: 8654k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1243708145.668:1): initialized
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 751
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
pci 0000:00:07.0: Disabling VIA external APIC routing
pci 0000:01:00.0: Boot video device
vesafb: framebuffer at 0xd0000000, mapped to 0xd8880000, using 3072k, total 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:c380
vesafb: pmi: set display start = c00cc3c5, set palette = c00cc44a
vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903 cc03 ce03 cf03 d003 d103 d203 d303 d403 d503 da03 ff03
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Fixed MDIO Bus: probed
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
IO APIC resources could be not be allocated.
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 352k freed
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
ACPI: CPU0 (power states: C1[C1] C2[C2])
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 2 throttling states)
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xd8000000
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
8139too 0000:00:09.0: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xd8cee000, 00:0a:cd:02:cc:a1, IRQ 10
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
aic7xxx 0000:00:0b.0: PCI INT A -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
uhci_hcd: USB Universal Host Controller Interface driver
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
libata version 3.00 loaded.
Marking TSC unstable due to TSC halts in idle
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
        <Adaptec 2940 SCSI adapter>
        aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs

uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000c400
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.29-4.slh.4-sidux-686 uhci_hcd
usb usb1: SerialNumber: 0000:00:07.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:07.3: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.3: irq 11, io base 0x0000c800
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.29-4.slh.4-sidux-686 uhci_hcd
usb usb2: SerialNumber: 0000:00:07.3
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
pata_via 0000:00:07.1: version 0.3.3
scsi1 : pata_via
scsi2 : pata_via
ata1: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma 0xc000 irq 14
ata2: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xc008 irq 15
ata1.00: native sectors (39102335) is smaller than sectors (39102336)
ata1.00: ATA-4: ST320413A, 3.36, max UDMA/100
ata1.00: 39102336 sectors, multi 16: LBA
ata1.01: ATA-5: QUANTUM FIREBALLlct15 10, A01.0F00, max UDMA/66
ata1.01: 20044080 sectors, multi 16: LBA
ata1.00: configured for UDMA/66
ata1.01: configured for UDMA/66
scsi: waiting for bus probes to complete ...
scsi 1:0:0:0: Direct-Access     ATA      ST320413A        3.36 PQ: 0 ANSI: 5
scsi 1:0:1:0: Direct-Access     ATA      QUANTUM FIREBALL A01. PQ: 0 ANSI: 5
ata2.00: ATA-4: ST310232A, 3.09, max UDMA/66
ata2.00: 19541088 sectors, multi 16: LBA
ata2.01: ATAPI: SONY    CD-RW  CRX215E1, SYS2, max UDMA/33
ata2.00: configured for UDMA/66
ata2.01: configured for UDMA/33
scsi 2:0:0:0: Direct-Access     ATA      ST310232A        3.09 PQ: 0 ANSI: 5
scsi 2:0:1:0: CD-ROM            SONY     CD-RW  CRX215E1  SYS2 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 1:0:0:0: [sda] 39102336 512-byte hardware sectors: (20.0 GB/18.6 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 39102336 512-byte hardware sectors: (20.0 GB/18.6 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:1:0: [sdb] 20044080 512-byte hardware sectors: (10.2 GB/9.55 GiB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:1:0: [sdb] 20044080 512-byte hardware sectors: (10.2 GB/9.55 GiB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb:<4>Driver 'sr' needs updating - please use bus_type methods
 sdb1 sdb2 sdb3
sd 1:0:1:0: [sdb] Attached SCSI disk
sd 2:0:0:0: [sdc] 19541088 512-byte hardware sectors: (10.0 GB/9.31 GiB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdc] 19541088 512-byte hardware sectors: (10.0 GB/9.31 GiB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk
sr0: scsi3-mmc drive: 93x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:1:0: Attached scsi CD-ROM sr0
sd 1:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:1:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
sr 2:0:1:0: Attached scsi generic sg3 type 5
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
udevd version 125 started
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
ACPI: Sleep Button (CM) [SLPB]
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 242 bytes nvram
input: PC Speaker as /devices/platform/pcspkr/input/input5
psmouse serio1: ID: 00 00 3c<6>input: PS/2 Logitech Mouse as /devices/platform/i8042/serio1/input/input6
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
VIA 82xx Audio 0000:00:07.5: PCI INT C -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
VIA 82xx Audio 0000:00:07.5: VIA VLink IRQ fixup, from 9 to 10
VIA 82xx Audio 0000:00:07.5: setting latency timer to 64
Control name 'Sigmatel Surround Phase Inversion Playback Switch' truncated to 'Sigmatel Surround Phase Inversion Playback '
Adding 393584k swap on /dev/sdb2.  Priority:-1 extents:1 across:393584k
Adding 393552k swap on /dev/sdc1.  Priority:-2 extents:1 across:393552k
EXT3 FS on sdb3, internal journal
fuse init (API version 7.11)
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdc2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link up, 10Mbps, half-duplex, lpa 0x0000
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
lp0: using parport0 (interrupt-driven).
lp0: console ready
ppdev: user-space parallel port driver
eth0: no IPv6 routers present
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
nvidia 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 5 (level, low) -> IRQ 5
NVRM: loading NVIDIA Linux x86 Kernel Module  96.43.11  Mon Feb 23 15:29:05 PST 2009
IRQ 5/nvidia: IRQF_DISABLED is not guaranteed on shared IRQs
agpgart-via 0000:00:00.0: AGP 2.0 bridge
agpgart-via 0000:00:00.0: putting AGP V2 device into 4x mode
nvidia 0000:01:00.0: putting AGP V2 device into 4x mode
usb 2-2: new full speed USB device using uhci_hcd and address 2
usb 2-2: New USB device found, idVendor=06bd, idProduct=0403
usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 2-2: configuration #0 chosen from 1 choice
usb 2-2: config 0 descriptor??
process `skype' is using obsolete setsockopt SO_BSDCOMPAT

Kod:

root@siduxbox:/home/krzysztof# uname -r
2.6.29-4.slh.4-sidux-686

Offline

 

#2  2009-05-30 20:19:00

  ilin - Palacz

ilin
Palacz
Skąd: PRLu
Zarejestrowany: 2006-05-03

Re: kamera AGFA CL18.

Obawiam sie ze z tym mogą być problemy.

W tym aparacie pewnie jest zmiana trybu pracy na kamera.

Wlącz w tryb kamera i wtedy zobacz  lsusb

Porównamy czy nie zmieniło się przypadkiem ID.

Bo tylko po ID możemy w goglownicy szukać coś na ten temat.


Problemy rozwiązujemy na forum nie na PW -> Niech inni na tym skorzystają.
Polski portal Debiana

Offline

 

#3  2009-05-30 20:58:32

  reinkkrz - Użytkownik

reinkkrz
Użytkownik
Skąd: Nakło nad Notecią
Zarejestrowany: 2009-05-11

Re: kamera AGFA CL18.

brak w aparacie zmiany trybu pracy
pod Windows tylko zainstalowałem odpowiedni sterownik i wszystko działało .

Offline

 

#4  2009-05-30 21:37:00

  ilin - Palacz

ilin
Palacz
Skąd: PRLu
Zarejestrowany: 2006-05-03

Re: kamera AGFA CL18.

Bo w windowsie są pod to dedykowane sterowniki.
Tu trzeba kombinować jak się da (jeśli się da)

Pogoglam jeszcze ale raczej marne szanse.


Problemy rozwiązujemy na forum nie na PW -> Niech inni na tym skorzystają.
Polski portal Debiana

Offline

 

#5  2009-05-30 23:10:43

  fnmirk - Redaktor

fnmirk
Redaktor
Zarejestrowany: 2008-02-19

Re: kamera AGFA CL18.

Takie coś ale nie wiem czy będzie działać?
http://ubuntuforums.org/showpost.php?s=9abb02d01d3d … p;postcount=1

Edit:
Wygląda że jest prawie podobna?

Ostatnio edytowany przez fnmirk (2009-05-30 23:12:00)

Offline

 

#6  2009-05-31 07:56:26

  ilin - Palacz

ilin
Palacz
Skąd: PRLu
Zarejestrowany: 2006-05-03

Re: kamera AGFA CL18.

Hmm

Tyle ze to jest podlączenie jako aparat.(do zrzucania zdjęć)
Sedno pytania  zas dotyczy jak uruchomić to jako kamera internetowa.


Problemy rozwiązujemy na forum nie na PW -> Niech inni na tym skorzystają.
Polski portal Debiana

Offline

 

#7  2009-06-07 00:09:11

  reinkkrz - Użytkownik

reinkkrz
Użytkownik
Skąd: Nakło nad Notecią
Zarejestrowany: 2009-05-11

Re: kamera AGFA CL18.

Witam
Znalazłem stronę z sterownikiem DC2xx
http://www.qbik.ch/usb/devices/showdev.php?id=480
ale nie wiem jak zainstalować plik dc2xx.c  ?
proszę o szczegółowy opis.
Pozdrawiam.

Ostatnio edytowany przez reinkkrz (2009-06-07 00:10:05)

Offline

 

#8  2009-06-07 08:15:13

  ilin - Palacz

ilin
Palacz
Skąd: PRLu
Zarejestrowany: 2006-05-03

Re: kamera AGFA CL18.

Zwróć uwagę na datę tego sterownika.
Zresztą link do niego i tak nie działa.

To było w okresie jak były jądra 2.2- 2.4  co najwyżej.
Prawdopodpobnie i tak tylko dotyczył on zrzucnia zdjęć.
Tak że niestety radość przedwczesna.


Problemy rozwiązujemy na forum nie na PW -> Niech inni na tym skorzystają.
Polski portal Debiana

Offline

 

Stopka forum

Powered by PunBB
© Copyright 2002–2005 Rickard Andersson
Możesz wyłączyć AdBlock — tu nie ma reklam ;-)