Forum Debian Users Gang

cze
wgralem debiana 3.1 (z opcja "linux26" - czyli mam jajko 2.6.8) na mojego kompa

Proc: P4 3Ghz HT
Plyta: ASROCK 775Twins-HDTV

i nie wykyl mi calego sprzetu

w manualu od plyty pisze
Northbridge: ATI Radeon Xpress 200 chipset
Southbridge: ULI 1573

LAN: Realtek PHY RTL8201CL
        Speed: 10/100Mb Ethernet

jak wpisze lspci:
pcilib: Cannot open /sys/bus/pci/devices
0000:00:00.0 Host bridge: ATI Technologies Inc: Unknown device 5a33 (rev 01)
0000:00:01.0 PCI bridge: ATI Technologies Inc: Unknown device 5a3f
0000:00:19.0 PCI bridge: ALi Corporation M5249 HTT to PCI Bridge
0000:00:1b.0 Ethernet controller: ALi Corporation: Unknown device 5263 (rev 50)
0000:00:1c.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
0000:00:1c.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
0000:00:1c.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
0000:00:1c.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01)
0000:00:1d.0 Multimedia audio controller: ALi Corporation M5455 PCI AC-Link Controller Audio Device (rev 20)
0000:00:1e.0 ISA bridge: ALi Corporation: Unknown device 1573 (rev 31)
0000:00:1e.1 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
0000:00:1f.0 IDE interface: ALi Corporation M5229 IDE (rev c7)
0000:00:1f.1 0106: ALi Corporation: Unknown device 5287 (rev 02)
0000:01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5a61
0000:02:15.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
0000:02:15.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
0000:02:16.0 Ethernet controller: Linksys NC100 Network Everywhere Fast Ethernet 10/100 (rev 11)

kompiluje wlasnie nowe jajko 2.6.18, dodalem w SCSI -> Low ... -> ULI Drivera i dodalem w Drivers -> Network -> Tulip -> moja sieciowke 

NA tym samym kompie mialem wczesniej wgranego SUSE 10.1 i tam wykryl wszystko (prawie :) ) 2.6.16.13-4-smp.

oto lspci z suse 10.1

00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a33 (rev 01)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:19.0 PCI bridge: ALi Corporation M5249 HTT to PCI Bridge
00:1b.0 Ethernet controller: ALi Corporation M5263 Ethernet Controller (rev 50)
00:1c.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01)
00:1d.0 Multimedia audio controller: ALi Corporation M5455 PCI AC-Link Controller Audio Device (rev 20)
00:1e.0 ISA bridge: ALi Corporation PCI to LPC Controller (rev 31)
00:1e.1 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
00:1f.0 IDE interface: ALi Corporation M5229 IDE (rev c7)
00:1f.1 SATA controller: ALi Corporation ULi 5287 SATA (rev 02)
01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon Xpress 200]
02:15.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
02:15.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
02:16.0 Ethernet controller: Linksys NC100 Network Everywhere Fast Ethernet 10/100 (rev 11)


nadal brakuje mi 00:01.0 - 00:1e.0 - 1:05.0

no i teraz nie wiem ale ja w tym "make menuconfig" za chiny tych sterownikow nie widze :(