Nie jesteś zalogowany.
Jeśli nie posiadasz konta, zarejestruj je już teraz! Pozwoli Ci ono w pełni korzystać z naszego serwisu. Spamerom dziękujemy!

Ogłoszenie

Prosimy o pomoc dla małej Julki — przekaż 1% podatku na Fundację Dzieciom „Zdążyć z Pomocą”.
Więcej informacji na dug.net.pl/pomagamy/.

#1 2018-02-12 21:15:20

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Debian Stretch i problemy z instalacją i po instalacji

Zainstalowałem pierwszy raz w życiu Debiana. Problemy były od początku z instalacją; płyta cd po zabotowaniu , w jakimś nie określonym
momencie instalacji się pikselowała uniemożliwiając dalszą instalację. Potem padła decyzja o instalqacji z pena ; zrobiłem pena w Rufusie to
z kolei nie mogłem zabotować. Płyta staroć na 939 A8N SLI DELUKSE ASUSA z 2004 roku. Problem z botowaniem rozwiązałem za pomocą PLOP na cd , polecam fajne rozwiązanie.

Po instalacji , kilkukrotnej z powodów opisanych wyżej   Debian szybko chodzi (podoba mi się ), środowisko graficzne to MATE.
Jest jednak jeden problem; z niewiadomego powodu i w nieokreślonym czasie zamraża się wszystko. 
Obraz jest ok. nie uszkodzony w żadnym stopniu, zamraża się wszystko totalnie , jedynie myszką po ekranie można
latać bez możliwości zrobienia czegokolwiek.   Komp jest stary jednak na miejscu Debiana do przedwczoraj bardzo fajnie latało Ubuntu 12.04.
Debian stoi na pierwszej partycji nowego 1 TB dysku Seagate, innego systemu na tym dysku nie ma i nie będzie. Na innych dyskach mam 2 Xpeki  z Sp3,
które w miarę dobrze sobie radzą.

Piszę o tym dlatego żeby poinformować ,że raczej na winę sprzętu nic nie wskazuje. Debian dał sobie bez problemu zainstalować Pidgina , Jpk2, gpgsm.
Jest natomiast problem z aptem ; przy próbie instalacji sterowników Nvidi dla czipa NV-44x czyli jeszcze 6600 GT nie mogę nic pobrać ani zrobić. 
Polecenie $ nvidia-detect nie wyświetla wyniku i dużo poleceń apta dotyczących systemu nie działa  .
Najbardziej zależy mi na znalezieniu rozwiązania problemu z tym zawieszaniem się systemu.

Nie wykluczam osobiście problemu ze sprzętem.

Ostatnio edytowany przez Ainat (2018-02-12 21:44:21)

Offline

 

#2 2018-02-13 10:26:25

Jacekalex
Podobno człowiek...;)
Skąd: /dev/urandom
Zarejestrowany: 2008-01-07

Re: Debian Stretch i problemy z instalacją i po instalacji

Jak się system wiesza, czy "zamraża" to potrzebny jest /var/log/kern.log
wrzuć na pastebina i daj sznurka.

Oczywiście to w przypadku, kiedy wiesza się cały system, i np nie odpowiada na pingi z innego kompa.

Jeżeli wiesza się sam Xorg (i blokuje klawiaturę i myszkę), to przydałby się

Kod:

/var/log/Xorg.0.log

z takiego powieszenia.

Takie logi mogą być w różnych plikach, zobacz

Kod:

ls  /var/log/Xorg.*

i uściślij, co to znaczy "nie mogę zainstalować sterownika", bo to trochę dziwne.
Pokaż wykonany z konta root wynik:

Kod:

apt install nvidia-detect 
nvidia-detect

PS.
Prawidłowy wynik wyjścia nvidia-detect powinien wyglądać podobnie do tego:

Kod:

# Debian ###   wto lut 13 10:26:41  domek : / 
root ~>  nvidia-detect
Detected NVIDIA GPUs:
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GM107 [GeForce GTX 750] [10de:1381] (rev a2)

Checking card:  NVIDIA Corporation GM107 [GeForce GTX 750] (rev a2)
Your card is supported by the default drivers and legacy driver series 340.
It is recommended to install the
    nvidia-driver
package.

Pozdro

Ostatnio edytowany przez Jacekalex (2018-02-13 10:29:42)


W demokracji każdy naród ma taką władzę, na jaką zasługuje ;)
Si vis pacem  para bellum  ;)       |       Pozdrawiam :)

Offline

 

#3 2018-02-14 12:48:11

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

kern.log jest tutaj ( na podanej stronie był za duzy)  https://drive.google.com/file/d/1XteGzKoTWM9j-PH6ui … w?usp=sharing

Xorg.0.log   

Kod:

X.Org X Server 1.19.2
Release Date: 2017-03-02
[    11.867] X Protocol Version 11, Revision 0
[    11.867] Build Operating System: Linux 4.9.0-4-amd64 x86_64 Debian
[    11.867] Current Operating System: Linux Stretch 4.9.0-4-amd64 #1 SMP Debian 4.9.65-3 (2017-12-03) x86_64
[    11.867] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.9.0-4-amd64 root=/dev/sda1 ro quiet
[    11.867] Build Date: 16 October 2017  08:19:45AM
[    11.867] xorg-server 2:1.19.2-1+deb9u2 (https://www.debian.org/support)
[    11.867] Current version of pixman: 0.34.0
[    11.867]    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
[    11.867] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    11.867] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Feb 14 11:12:49 2018
[    11.882] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    11.892] (==) No Layout section.  Using the first Screen section.
[    11.892] (==) No screen section available. Using defaults.
[    11.892] (**) |-->Screen "Default Screen Section" (0)
[    11.892] (**) |   |-->Monitor "<default monitor>"
[    11.894] (==) No monitor specified for screen "Default Screen Section".
    Using a default monitor configuration.
[    11.894] (==) Automatically adding devices
[    11.894] (==) Automatically enabling devices
[    11.894] (==) Automatically adding GPU devices
[    11.894] (==) Max clients allowed: 256, resource mask: 0x1fffff
[    11.915] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    11.915]    Entry deleted from font path.
[    11.919] (==) FontPath set to:
    /usr/share/fonts/X11/misc,
    /usr/share/fonts/X11/100dpi/:unscaled,
    /usr/share/fonts/X11/75dpi/:unscaled,
    /usr/share/fonts/X11/Type1,
    /usr/share/fonts/X11/100dpi,
    /usr/share/fonts/X11/75dpi,
    built-ins
[    11.919] (==) ModulePath set to "/usr/lib/xorg/modules"
[    11.919] (II) The server relies on udev to provide the list of input devices.
    If no devices become available, reconfigure udev or disable AutoAddDevices.
[    11.919] (II) Loader magic: 0x5561fdc6fe00
[    11.919] (II) Module ABI versions:
[    11.919]    X.Org ANSI C Emulation: 0.4
[    11.919]    X.Org Video Driver: 23.0
[    11.919]    X.Org XInput driver : 24.1
[    11.919]    X.Org Server Extension : 10.0
[    11.921] (++) using VT number 7
 
[    11.921] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[    11.922] (II) xfree86: Adding drm device (/dev/dri/card0)
[    11.925] (--) PCI:*(0:1:0:0) 10de:0140:1458:3125 rev 162, Mem @ 0xc8000000/67108864, 0xc0000000/134217728, 0xcc000000/16777216, BIOS @ 0x????????/131072
[    11.925] (II) LoadModule: "glx"
[    11.927] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    11.980] (II) Module glx: vendor="X.Org Foundation"
[    11.980]    compiled for 1.19.2, module version = 1.0.0
[    11.981]    ABI class: X.Org Server Extension, version 10.0
[    11.981] (==) Matched nouveau as autoconfigured driver 0
[    11.981] (==) Matched nv as autoconfigured driver 1
[    11.981] (==) Matched nouveau as autoconfigured driver 2
[    11.981] (==) Matched nv as autoconfigured driver 3
[    11.981] (==) Matched modesetting as autoconfigured driver 4
[    11.981] (==) Matched fbdev as autoconfigured driver 5
[    11.981] (==) Matched vesa as autoconfigured driver 6
[    11.981] (==) Assigned the driver to the xf86ConfigLayout
[    11.981] (II) LoadModule: "nouveau"
[    11.981] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[    11.991] (II) Module nouveau: vendor="X.Org Foundation"
[    11.991]    compiled for 1.19.3, module version = 1.0.13
[    11.991]    Module class: X.Org Video Driver
[    11.991]    ABI class: X.Org Video Driver, version 23.0
[    11.991] (II) LoadModule: "nv"
[    11.992] (WW) Warning, couldn't open module nv
[    11.992] (II) UnloadModule: "nv"
[    11.992] (II) Unloading nv
[    11.992] (EE) Failed to load module "nv" (module does not exist, 0)
[    11.992] (II) LoadModule: "modesetting"
[    11.992] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[    11.994] (II) Module modesetting: vendor="X.Org Foundation"
[    11.994]    compiled for 1.19.2, module version = 1.19.2
[    11.994]    Module class: X.Org Video Driver
[    11.994]    ABI class: X.Org Video Driver, version 23.0
[    11.994] (II) LoadModule: "fbdev"
[    11.994] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[    11.995] (II) Module fbdev: vendor="X.Org Foundation"
[    11.995]    compiled for 1.19.0, module version = 0.4.4
[    11.995]    Module class: X.Org Video Driver
[    11.995]    ABI class: X.Org Video Driver, version 23.0
[    11.995] (II) LoadModule: "vesa"
[    11.995] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[    11.996] (II) Module vesa: vendor="X.Org Foundation"
[    11.996]    compiled for 1.19.0, module version = 2.3.4
[    11.996]    Module class: X.Org Video Driver
[    11.996]    ABI class: X.Org Video Driver, version 23.0
[    11.996] (II) NOUVEAU driver Date:   Tue Sep 20 00:31:06 2016 -0400
[    11.997] (II) NOUVEAU driver for NVIDIA chipset families :
[    11.997]    RIVA TNT        (NV04)
[    11.997]    RIVA TNT2       (NV05)
[    11.997]    GeForce 256     (NV10)
[    11.997]    GeForce 2       (NV11, NV15)
[    11.997]    GeForce 4MX     (NV17, NV18)
[    11.997]    GeForce 3       (NV20)
[    11.997]    GeForce 4Ti     (NV25, NV28)
[    11.997]    GeForce FX      (NV3x)
[    11.997]    GeForce 6       (NV4x)
[    11.997]    GeForce 7       (G7x)
[    11.997]    GeForce 8       (G8x)
[    11.997]    GeForce GTX 200 (NVA0)
[    11.997]    GeForce GTX 400 (NVC0)
[    11.997] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[    11.998] (II) FBDEV: driver for framebuffer: fbdev
[    11.998] (II) VESA: driver for VESA chipsets: vesa
[    12.000] (II) [drm] nouveau interface version: 1.3.1
[    12.001] (WW) Falling back to old probe method for modesetting
[    12.001] (WW) Falling back to old probe method for fbdev
[    12.001] (II) Loading sub module "fbdevhw"
[    12.001] (II) LoadModule: "fbdevhw"
[    12.001] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[    12.002] (II) Module fbdevhw: vendor="X.Org Foundation"
[    12.002]    compiled for 1.19.2, module version = 0.0.2
[    12.002]    ABI class: X.Org Video Driver, version 23.0
[    12.003] (WW) Falling back to old probe method for vesa
[    12.003] (II) Loading sub module "dri2"
[    12.003] (II) LoadModule: "dri2"
[    12.003] (II) Module "dri2" already built-in
[    12.003] (--) NOUVEAU(0): Chipset: "NVIDIA NV43"
[    12.003] (II) NOUVEAU(0): Creating default Display subsection in Screen section
    "Default Screen Section" for depth/fbbpp 24/32
[    12.003] (==) NOUVEAU(0): Depth 24, (--) framebuffer bpp 32
[    12.003] (==) NOUVEAU(0): RGB weight 888
[    12.003] (==) NOUVEAU(0): Default visual is TrueColor
[    12.003] (==) NOUVEAU(0): Using HW cursor
[    12.003] (==) NOUVEAU(0): Allowed maximum DRI level 2.
[    12.003] (==) NOUVEAU(0): GLX sync to VBlank enabled.
[    12.003] (==) NOUVEAU(0): Page flipping enabled
[    12.003] (==) NOUVEAU(0): Swap limit set to 1 [Max allowed 2]
[    12.003] (==) NOUVEAU(0): Page flipping synced to vblank by kernel.
[    12.003] (II) NOUVEAU(0): Initializing outputs ...
[    12.044] (II) NOUVEAU(0): Output VGA-1 has no monitor section
[    12.074] (II) NOUVEAU(0): Output DVI-I-1 has no monitor section
[    12.144] (II) NOUVEAU(0): Output TV-1 has no monitor section
[    12.144] (II) NOUVEAU(0): 3 crtcs needed for screen.
[    12.144] (II) NOUVEAU(0): Allocated crtc nr. 0 to this screen.
[    12.144] (II) NOUVEAU(0): Allocated crtc nr. 1 to this screen.
[    12.184] (II) NOUVEAU(0): EDID for output VGA-1
[    12.214] (II) NOUVEAU(0): EDID for output DVI-I-1
[    12.214] (II) NOUVEAU(0): Manufacturer: SAM  Model: 711  Serial#: 858796596
[    12.214] (II) NOUVEAU(0): Year: 2010  Week: 11
[    12.214] (II) NOUVEAU(0): EDID Version: 1.3
[    12.214] (II) NOUVEAU(0): Analog Display Input,  Input Voltage Level: 0.700/0.300 V
[    12.214] (II) NOUVEAU(0): Sync:  Separate  Composite  SyncOnGreen
[    12.215] (II) NOUVEAU(0): Max Image Size [cm]: horiz.: 53  vert.: 30
[    12.215] (II) NOUVEAU(0): Gamma: 2.20
[    12.215] (II) NOUVEAU(0): DPMS capabilities: Off; RGB/Color Display
[    12.215] (II) NOUVEAU(0): First detailed timing is preferred mode
[    12.215] (II) NOUVEAU(0): redX: 0.640 redY: 0.330   greenX: 0.300 greenY: 0.600
[    12.215] (II) NOUVEAU(0): blueX: 0.150 blueY: 0.060   whiteX: 0.312 whiteY: 0.329
[    12.215] (II) NOUVEAU(0): Supported established timings:
[    12.215] (II) NOUVEAU(0): 720x400@70Hz
[    12.215] (II) NOUVEAU(0): 640x480@60Hz
[    12.215] (II) NOUVEAU(0): 640x480@67Hz
[    12.215] (II) NOUVEAU(0): 640x480@72Hz
[    12.215] (II) NOUVEAU(0): 640x480@75Hz
[    12.215] (II) NOUVEAU(0): 800x600@56Hz
[    12.215] (II) NOUVEAU(0): 800x600@60Hz
[    12.215] (II) NOUVEAU(0): 800x600@72Hz
[    12.215] (II) NOUVEAU(0): 800x600@75Hz
[    12.215] (II) NOUVEAU(0): 832x624@75Hz
[    12.215] (II) NOUVEAU(0): 1024x768@60Hz
[    12.215] (II) NOUVEAU(0): 1024x768@70Hz
[    12.215] (II) NOUVEAU(0): 1024x768@75Hz
[    12.215] (II) NOUVEAU(0): 1280x1024@75Hz
[    12.215] (II) NOUVEAU(0): 1152x864@75Hz
[    12.215] (II) NOUVEAU(0): Manufacturer's mask: 0
[    12.215] (II) NOUVEAU(0): Supported standard timings:
[    12.215] (II) NOUVEAU(0): #0: hsize: 1280  vsize 800  refresh: 60  vid: 129
[    12.215] (II) NOUVEAU(0): #1: hsize: 1440  vsize 900  refresh: 60  vid: 149
[    12.215] (II) NOUVEAU(0): #2: hsize: 1680  vsize 1050  refresh: 60  vid: 179
[    12.215] (II) NOUVEAU(0): #3: hsize: 1280  vsize 960  refresh: 60  vid: 16513
[    12.215] (II) NOUVEAU(0): #4: hsize: 1152  vsize 864  refresh: 75  vid: 20337
[    12.215] (II) NOUVEAU(0): #5: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    12.215] (II) NOUVEAU(0): #6: hsize: 1440  vsize 900  refresh: 75  vid: 3989
[    12.215] (II) NOUVEAU(0): Supported detailed timing:
[    12.215] (II) NOUVEAU(0): clock: 148.5 MHz   Image Size:  531 x 299 mm
[    12.215] (II) NOUVEAU(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[    12.215] (II) NOUVEAU(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    12.215] (II) NOUVEAU(0): Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[    12.215] (II) NOUVEAU(0): Monitor name: SMB2430HD
[    12.216] (II) NOUVEAU(0): Serial No: 0
[    12.216] (II) NOUVEAU(0): EDID (in hex):
[    12.216] (II) NOUVEAU(0):   00ffffffffffff004c2d110734323033
[    12.216] (II) NOUVEAU(0):   0b1401030e351e782aee91a3544c9926
[    12.216] (II) NOUVEAU(0):   0f5054bfef8081009500b3008140714f
[    12.216] (II) NOUVEAU(0):   8180950f0101023a801871382d40582c
[    12.216] (II) NOUVEAU(0):   4500132b2100001e000000fd00384b1e
[    12.216] (II) NOUVEAU(0):   5111000a202020202020000000fc0053
[    12.216] (II) NOUVEAU(0):   4d423234333048440a202020000000ff
[    12.216] (II) NOUVEAU(0):   00300a20202020202020202020200003
[    12.216] (II) NOUVEAU(0): Printing probed modes for output DVI-I-1
[    12.216] (II) NOUVEAU(0): Modeline "1920x1080"x60.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[    12.216] (II) NOUVEAU(0): Modeline "1680x1050"x60.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync (65.3 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1440x900"x75.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1440x900"x59.9  106.50  1440 1520 1672 1904  900 903 909 934 -hsync +vsync (55.9 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1280x800"x59.8   83.50  1280 1352 1480 1680  800 803 809 831 -hsync +vsync (49.7 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1152x864"x75.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1024x768"x70.1   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "832x624"x74.6   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "800x600"x72.2   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    12.217] (II) NOUVEAU(0): Modeline "640x480"x72.8   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz e)
[    12.217] (II) NOUVEAU(0): Modeline "640x480"x66.7   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz e)
[    12.217] (II) NOUVEAU(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    12.217] (II) NOUVEAU(0): Modeline "720x400"x70.1   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[    12.284] (II) NOUVEAU(0): EDID for output TV-1
[    12.284] (II) NOUVEAU(0): Printing probed modes for output TV-1
[    12.284] (II) NOUVEAU(0): Modeline "720x576"x50.0   28.66  720 776 856 960  576 576 588 597 -hsync -vsync (29.9 kHz eP)
[    12.284] (II) NOUVEAU(0): Modeline "1024x768"x50.0   54.16  1024 1064 1200 1344  768 768 777 806 -hsync -vsync (40.3 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "800x600"x50.0   32.14  800 840 920 1040  600 600 604 618 +hsync +vsync (30.9 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "720x480"x50.0   25.20  720 752 872 960  480 480 493 525 -hsync -vsync (26.2 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "640x480"x50.0   23.10  640 672 768 880  480 480 492 525 -hsync -vsync (26.2 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "400x300"x100.0   20.10  400 432 496 640  300 300 303 314 doublescan +hsync +vsync (31.4 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "320x240"x100.0   14.73  320 344 392 560  240 240 246 263 doublescan -hsync -vsync (26.3 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "320x200"x100.0   12.32  320 344 392 560  200 200 202 220 doublescan -hsync -vsync (22.0 kHz e)
[    12.284] (II) NOUVEAU(0): Output VGA-1 disconnected
[    12.284] (II) NOUVEAU(0): Output DVI-I-1 connected
[    12.284] (II) NOUVEAU(0): Output TV-1 connected
[    12.284] (II) NOUVEAU(0): Using spanning desktop for initial modes
[    12.284] (II) NOUVEAU(0): Output DVI-I-1 using initial mode 1920x1080 +0+0
[    12.284] (II) NOUVEAU(0): Output TV-1 using initial mode 720x576 +1920+0
[    12.284] (==) NOUVEAU(0): Using gamma correction (1.0, 1.0, 1.0)
[    12.284] (--) NOUVEAU(0): Virtual size is 2640x1080 (pitch 0)
[    12.284] (**) NOUVEAU(0):  Driver mode "720x576": 28.7 MHz (scaled from 0.0 MHz), 29.9 kHz, 50.0 Hz
[    12.284] (II) NOUVEAU(0): Modeline "720x576"x50.0   28.66  720 776 856 960  576 576 588 597 -hsync -vsync (29.9 kHz eP)
[    12.284] (**) NOUVEAU(0):  Driver mode "1024x768": 54.2 MHz (scaled from 0.0 MHz), 40.3 kHz, 50.0 Hz
[    12.284] (II) NOUVEAU(0): Modeline "1024x768"x50.0   54.16  1024 1064 1200 1344  768 768 777 806 -hsync -vsync (40.3 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "800x600": 32.1 MHz (scaled from 0.0 MHz), 30.9 kHz, 50.0 Hz
[    12.284] (II) NOUVEAU(0): Modeline "800x600"x50.0   32.14  800 840 920 1040  600 600 604 618 +hsync +vsync (30.9 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "720x480": 25.2 MHz (scaled from 0.0 MHz), 26.2 kHz, 50.0 Hz
[    12.284] (II) NOUVEAU(0): Modeline "720x480"x50.0   25.20  720 752 872 960  480 480 493 525 -hsync -vsync (26.2 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "640x480": 23.1 MHz (scaled from 0.0 MHz), 26.2 kHz, 50.0 Hz
[    12.284] (II) NOUVEAU(0): Modeline "640x480"x50.0   23.10  640 672 768 880  480 480 492 525 -hsync -vsync (26.2 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "400x300": 20.1 MHz (scaled from 0.0 MHz), 31.4 kHz, 100.0 Hz (D)
[    12.284] (II) NOUVEAU(0): Modeline "400x300"x100.0   20.10  400 432 496 640  300 300 303 314 doublescan +hsync +vsync (31.4 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "320x240": 14.7 MHz (scaled from 0.0 MHz), 26.3 kHz, 100.0 Hz (D)
[    12.284] (II) NOUVEAU(0): Modeline "320x240"x100.0   14.73  320 344 392 560  240 240 246 263 doublescan -hsync -vsync (26.3 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "320x200": 12.3 MHz (scaled from 0.0 MHz), 22.0 kHz, 100.0 Hz (D)
[    12.284] (II) NOUVEAU(0): Modeline "320x200"x100.0   12.32  320 344 392 560  200 200 202 220 doublescan -hsync -vsync (22.0 kHz e)
[    12.284] (==) NOUVEAU(0): DPI set to (96, 96)
[    12.284] (II) Loading sub module "fb"
[    12.285] (II) LoadModule: "fb"
[    12.285] (II) Loading /usr/lib/xorg/modules/libfb.so
[    12.287] (II) Module fb: vendor="X.Org Foundation"
[    12.287]    compiled for 1.19.2, module version = 1.0.0
[    12.287]    ABI class: X.Org ANSI C Emulation, version 0.4
[    12.287] (II) Loading sub module "shadowfb"
[    12.287] (II) LoadModule: "shadowfb"
[    12.287] (II) Loading /usr/lib/xorg/modules/libshadowfb.so
[    12.288] (II) Module shadowfb: vendor="X.Org Foundation"
[    12.288]    compiled for 1.19.2, module version = 1.0.0
[    12.288]    ABI class: X.Org ANSI C Emulation, version 0.4
[    12.288] (II) UnloadModule: "modesetting"
[    12.288] (II) Unloading modesetting
[    12.288] (II) UnloadModule: "fbdev"
[    12.288] (II) Unloading fbdev
[    12.288] (II) UnloadSubModule: "fbdevhw"
[    12.288] (II) Unloading fbdevhw
[    12.288] (II) UnloadModule: "vesa"
[    12.288] (II) Unloading vesa
[    12.288] (--) Depth 24 pixmap format is 32 bpp
[    12.290] (II) NOUVEAU(0): Channel setup complete.
[    12.294] (II) NOUVEAU(0): Hardware support for Present enabled
[    12.294] (II) NOUVEAU(0): [DRI2] Setup complete
[    12.294] (II) NOUVEAU(0): [DRI2]   DRI driver: nouveau
[    12.294] (II) NOUVEAU(0): [DRI2]   VDPAU driver: nouveau
[    12.294] (II) Loading sub module "exa"
[    12.294] (II) LoadModule: "exa"
[    12.294] (II) Loading /usr/lib/xorg/modules/libexa.so
[    12.296] (II) Module exa: vendor="X.Org Foundation"
[    12.296]    compiled for 1.19.2, module version = 2.6.0
[    12.296]    ABI class: X.Org Video Driver, version 23.0
[    12.296] (II) EXA(0): Driver allocated offscreen pixmaps
[    12.296] (II) EXA(0): Driver registered support for the following operations:
[    12.296] (II)         Solid
[    12.296] (II)         Copy
[    12.296] (II)         Composite (RENDER acceleration)
[    12.296] (II)         UploadToScreen
[    12.296] (II)         DownloadFromScreen
[    12.296] (==) NOUVEAU(0): Backing store enabled
[    12.296] (==) NOUVEAU(0): Silken mouse enabled
[    12.296] (II) NOUVEAU(0): [XvMC] Associated with NV40 texture adapter.
[    12.296] (II) NOUVEAU(0): [XvMC] Extension initialized.
[    12.296] (==) NOUVEAU(0): DPMS enabled
[    12.296] (II) NOUVEAU(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    12.298] (--) RandR disabled
[    12.306] (II) SELinux: Disabled on system
[    12.944] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[    12.944] (II) AIGLX: enabled GLX_ARB_create_context
[    12.944] (II) AIGLX: enabled GLX_ARB_create_context_profile
[    12.944] (II) AIGLX: enabled GLX_EXT_create_context_es{,2}_profile
[    12.944] (II) AIGLX: enabled GLX_INTEL_swap_event
[    12.944] (II) AIGLX: enabled GLX_SGI_swap_control
[    12.944] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[    12.944] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[    12.944] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float
[    12.944] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[    12.945] (II) AIGLX: Loaded and initialized nouveau
[    12.945] (II) GLX: Initialized DRI2 GL provider for screen 0
[    12.948] (II) NOUVEAU(0): NVEnterVT is called.
[    12.948] (II) NOUVEAU(0): Setting screen physical size to 698 x 285
[    12.948] resize called 2640 1080
[    13.298] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[    13.298] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    13.298] (II) LoadModule: "libinput"
[    13.299] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[    13.332] (II) Module libinput: vendor="X.Org Foundation"
[    13.332]    compiled for 1.19.0, module version = 0.23.0
[    13.332]    Module class: X.Org XInput Driver
[    13.332]    ABI class: X.Org XInput driver, version 24.1
[    13.332] (II) Using input driver 'libinput' for 'Power Button'
[    13.332] (**) Power Button: always reports core events
[    13.332] (**) Option "Device" "/dev/input/event3"
[    13.332] (**) Option "_source" "server/udev"
[    13.333] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard
[    13.333] (II) input device 'Power Button', /dev/input/event3 is a keyboard
[    13.360] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"
[    13.360] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    13.360] (**) Option "xkb_model" "pc105"
[    13.360] (**) Option "xkb_layout" "pl"
[    13.405] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard
[    13.405] (II) input device 'Power Button', /dev/input/event3 is a keyboard
[    13.406] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[    13.406] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    13.406] (II) Using input driver 'libinput' for 'Power Button'
[    13.406] (**) Power Button: always reports core events
[    13.406] (**) Option "Device" "/dev/input/event2"
[    13.406] (**) Option "_source" "server/udev"
[    13.406] (II) input device 'Power Button', /dev/input/event2 is tagged by udev as: Keyboard
[    13.406] (II) input device 'Power Button', /dev/input/event2 is a keyboard
[    13.416] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2/event2"
[    13.416] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[    13.416] (**) Option "xkb_model" "pc105"
[    13.416] (**) Option "xkb_layout" "pl"
[    13.417] (II) input device 'Power Button', /dev/input/event2 is tagged by udev as: Keyboard
[    13.417] (II) input device 'Power Button', /dev/input/event2 is a keyboard
[    13.417] (II) config/udev: Adding input device USB OPTICAL MOUSE  (/dev/input/event1)
[    13.417] (**) USB OPTICAL MOUSE : Applying InputClass "libinput pointer catchall"
[    13.417] (II) Using input driver 'libinput' for 'USB OPTICAL MOUSE '
[    13.417] (**) USB OPTICAL MOUSE : always reports core events
[    13.417] (**) Option "Device" "/dev/input/event1"
[    13.417] (**) Option "_source" "server/udev"
[    13.476] (II) input device 'USB OPTICAL MOUSE ', /dev/input/event1 is tagged by udev as: Mouse
[    13.476] (II) input device 'USB OPTICAL MOUSE ', /dev/input/event1 is a pointer caps
[    13.508] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:02.0/usb2/2-1/2-1:1.0/0003:275D:0BA6.0001/input/input1/event1"
[    13.508] (II) XINPUT: Adding extended input device "USB OPTICAL MOUSE " (type: MOUSE, id 8)
[    13.508] (**) Option "AccelerationScheme" "none"
[    13.508] (**) USB OPTICAL MOUSE : (accel) selected scheme none/0
[    13.508] (**) USB OPTICAL MOUSE : (accel) acceleration factor: 2.000
[    13.508] (**) USB OPTICAL MOUSE : (accel) acceleration threshold: 4
[    13.568] (II) input device 'USB OPTICAL MOUSE ', /dev/input/event1 is tagged by udev as: Mouse
[    13.568] (II) input device 'USB OPTICAL MOUSE ', /dev/input/event1 is a pointer caps
[    13.569] (II) config/udev: Adding input device USB OPTICAL MOUSE  (/dev/input/mouse0)
[    13.569] (II) No input driver specified, ignoring this device.
[    13.569] (II) This device may have been added with another device file.
[    13.570] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[    13.570] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[    13.570] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[    13.570] (**) AT Translated Set 2 keyboard: always reports core events
[    13.570] (**) Option "Device" "/dev/input/event0"
[    13.570] (**) Option "_source" "server/udev"
[    13.570] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard
[    13.570] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard
[    13.600] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[    13.600] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 9)
[    13.600] (**) Option "xkb_model" "pc105"
[    13.600] (**) Option "xkb_layout" "pl"
[    13.601] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard
[    13.601] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard
[    13.602] (II) config/udev: Adding input device PC Speaker (/dev/input/event4)
[    13.602] (II) No input driver specified, ignoring this device.
[    13.602] (II) This device may have been added with another device file.[    11.867]

Xorg.0.log.old

Kod:

[    11.867] 
X.Org X Server 1.19.2
Release Date: 2017-03-02
[    11.867] X Protocol Version 11, Revision 0
[    11.867] Build Operating System: Linux 4.9.0-4-amd64 x86_64 Debian
[    11.867] Current Operating System: Linux Stretch 4.9.0-4-amd64 #1 SMP Debian 4.9.65-3 (2017-12-03) x86_64
[    11.867] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.9.0-4-amd64 root=/dev/sda1 ro quiet
[    11.867] Build Date: 16 October 2017  08:19:45AM
[    11.867] xorg-server 2:1.19.2-1+deb9u2 (https://www.debian.org/support) 
[    11.867] Current version of pixman: 0.34.0
[    11.867]     Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
[    11.867] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    11.867] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Feb 14 11:12:49 2018
[    11.882] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    11.892] (==) No Layout section.  Using the first Screen section.
[    11.892] (==) No screen section available. Using defaults.
[    11.892] (**) |-->Screen "Default Screen Section" (0)
[    11.892] (**) |   |-->Monitor "<default monitor>"
[    11.894] (==) No monitor specified for screen "Default Screen Section".
    Using a default monitor configuration.
[    11.894] (==) Automatically adding devices
[    11.894] (==) Automatically enabling devices
[    11.894] (==) Automatically adding GPU devices
[    11.894] (==) Max clients allowed: 256, resource mask: 0x1fffff
[    11.915] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    11.915]     Entry deleted from font path.
[    11.919] (==) FontPath set to:
    /usr/share/fonts/X11/misc,
    /usr/share/fonts/X11/100dpi/:unscaled,
    /usr/share/fonts/X11/75dpi/:unscaled,
    /usr/share/fonts/X11/Type1,
    /usr/share/fonts/X11/100dpi,
    /usr/share/fonts/X11/75dpi,
    built-ins
[    11.919] (==) ModulePath set to "/usr/lib/xorg/modules"
[    11.919] (II) The server relies on udev to provide the list of input devices.
    If no devices become available, reconfigure udev or disable AutoAddDevices.
[    11.919] (II) Loader magic: 0x5561fdc6fe00
[    11.919] (II) Module ABI versions:
[    11.919]     X.Org ANSI C Emulation: 0.4
[    11.919]     X.Org Video Driver: 23.0
[    11.919]     X.Org XInput driver : 24.1
[    11.919]     X.Org Server Extension : 10.0
[    11.921] (++) using VT number 7

[    11.921] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[    11.922] (II) xfree86: Adding drm device (/dev/dri/card0)
[    11.925] (--) PCI:*(0:1:0:0) 10de:0140:1458:3125 rev 162, Mem @ 0xc8000000/67108864, 0xc0000000/134217728, 0xcc000000/16777216, BIOS @ 0x????????/131072
[    11.925] (II) LoadModule: "glx"
[    11.927] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    11.980] (II) Module glx: vendor="X.Org Foundation"
[    11.980]     compiled for 1.19.2, module version = 1.0.0
[    11.981]     ABI class: X.Org Server Extension, version 10.0
[    11.981] (==) Matched nouveau as autoconfigured driver 0
[    11.981] (==) Matched nv as autoconfigured driver 1
[    11.981] (==) Matched nouveau as autoconfigured driver 2
[    11.981] (==) Matched nv as autoconfigured driver 3
[    11.981] (==) Matched modesetting as autoconfigured driver 4
[    11.981] (==) Matched fbdev as autoconfigured driver 5
[    11.981] (==) Matched vesa as autoconfigured driver 6
[    11.981] (==) Assigned the driver to the xf86ConfigLayout
[    11.981] (II) LoadModule: "nouveau"
[    11.981] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[    11.991] (II) Module nouveau: vendor="X.Org Foundation"
[    11.991]     compiled for 1.19.3, module version = 1.0.13
[    11.991]     Module class: X.Org Video Driver
[    11.991]     ABI class: X.Org Video Driver, version 23.0
[    11.991] (II) LoadModule: "nv"
[    11.992] (WW) Warning, couldn't open module nv
[    11.992] (II) UnloadModule: "nv"
[    11.992] (II) Unloading nv
[    11.992] (EE) Failed to load module "nv" (module does not exist, 0)
[    11.992] (II) LoadModule: "modesetting"
[    11.992] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[    11.994] (II) Module modesetting: vendor="X.Org Foundation"
[    11.994]     compiled for 1.19.2, module version = 1.19.2
[    11.994]     Module class: X.Org Video Driver
[    11.994]     ABI class: X.Org Video Driver, version 23.0
[    11.994] (II) LoadModule: "fbdev"
[    11.994] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[    11.995] (II) Module fbdev: vendor="X.Org Foundation"
[    11.995]     compiled for 1.19.0, module version = 0.4.4
[    11.995]     Module class: X.Org Video Driver
[    11.995]     ABI class: X.Org Video Driver, version 23.0
[    11.995] (II) LoadModule: "vesa"
[    11.995] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[    11.996] (II) Module vesa: vendor="X.Org Foundation"
[    11.996]     compiled for 1.19.0, module version = 2.3.4
[    11.996]     Module class: X.Org Video Driver
[    11.996]     ABI class: X.Org Video Driver, version 23.0
[    11.996] (II) NOUVEAU driver Date:   Tue Sep 20 00:31:06 2016 -0400
[    11.997] (II) NOUVEAU driver for NVIDIA chipset families :
[    11.997]     RIVA TNT        (NV04)
[    11.997]     RIVA TNT2       (NV05)
[    11.997]     GeForce 256     (NV10)
[    11.997]     GeForce 2       (NV11, NV15)
[    11.997]     GeForce 4MX     (NV17, NV18)
[    11.997]     GeForce 3       (NV20)
[    11.997]     GeForce 4Ti     (NV25, NV28)
[    11.997]     GeForce FX      (NV3x)
[    11.997]     GeForce 6       (NV4x)
[    11.997]     GeForce 7       (G7x)
[    11.997]     GeForce 8       (G8x)
[    11.997]     GeForce GTX 200 (NVA0)
[    11.997]     GeForce GTX 400 (NVC0)
[    11.997] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[    11.998] (II) FBDEV: driver for framebuffer: fbdev
[    11.998] (II) VESA: driver for VESA chipsets: vesa
[    12.000] (II) [drm] nouveau interface version: 1.3.1
[    12.001] (WW) Falling back to old probe method for modesetting
[    12.001] (WW) Falling back to old probe method for fbdev
[    12.001] (II) Loading sub module "fbdevhw"
[    12.001] (II) LoadModule: "fbdevhw"
[    12.001] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[    12.002] (II) Module fbdevhw: vendor="X.Org Foundation"
[    12.002]     compiled for 1.19.2, module version = 0.0.2
[    12.002]     ABI class: X.Org Video Driver, version 23.0
[    12.003] (WW) Falling back to old probe method for vesa
[    12.003] (II) Loading sub module "dri2"
[    12.003] (II) LoadModule: "dri2"
[    12.003] (II) Module "dri2" already built-in
[    12.003] (--) NOUVEAU(0): Chipset: "NVIDIA NV43"
[    12.003] (II) NOUVEAU(0): Creating default Display subsection in Screen section
    "Default Screen Section" for depth/fbbpp 24/32
[    12.003] (==) NOUVEAU(0): Depth 24, (--) framebuffer bpp 32
[    12.003] (==) NOUVEAU(0): RGB weight 888
[    12.003] (==) NOUVEAU(0): Default visual is TrueColor
[    12.003] (==) NOUVEAU(0): Using HW cursor
[    12.003] (==) NOUVEAU(0): Allowed maximum DRI level 2.
[    12.003] (==) NOUVEAU(0): GLX sync to VBlank enabled.
[    12.003] (==) NOUVEAU(0): Page flipping enabled
[    12.003] (==) NOUVEAU(0): Swap limit set to 1 [Max allowed 2]
[    12.003] (==) NOUVEAU(0): Page flipping synced to vblank by kernel.
[    12.003] (II) NOUVEAU(0): Initializing outputs ...
[    12.044] (II) NOUVEAU(0): Output VGA-1 has no monitor section
[    12.074] (II) NOUVEAU(0): Output DVI-I-1 has no monitor section
[    12.144] (II) NOUVEAU(0): Output TV-1 has no monitor section
[    12.144] (II) NOUVEAU(0): 3 crtcs needed for screen.
[    12.144] (II) NOUVEAU(0): Allocated crtc nr. 0 to this screen.
[    12.144] (II) NOUVEAU(0): Allocated crtc nr. 1 to this screen.
[    12.184] (II) NOUVEAU(0): EDID for output VGA-1
[    12.214] (II) NOUVEAU(0): EDID for output DVI-I-1
[    12.214] (II) NOUVEAU(0): Manufacturer: SAM  Model: 711  Serial#: 858796596
[    12.214] (II) NOUVEAU(0): Year: 2010  Week: 11
[    12.214] (II) NOUVEAU(0): EDID Version: 1.3
[    12.214] (II) NOUVEAU(0): Analog Display Input,  Input Voltage Level: 0.700/0.300 V
[    12.214] (II) NOUVEAU(0): Sync:  Separate  Composite  SyncOnGreen
[    12.215] (II) NOUVEAU(0): Max Image Size [cm]: horiz.: 53  vert.: 30
[    12.215] (II) NOUVEAU(0): Gamma: 2.20
[    12.215] (II) NOUVEAU(0): DPMS capabilities: Off; RGB/Color Display
[    12.215] (II) NOUVEAU(0): First detailed timing is preferred mode
[    12.215] (II) NOUVEAU(0): redX: 0.640 redY: 0.330   greenX: 0.300 greenY: 0.600
[    12.215] (II) NOUVEAU(0): blueX: 0.150 blueY: 0.060   whiteX: 0.312 whiteY: 0.329
[    12.215] (II) NOUVEAU(0): Supported established timings:
[    12.215] (II) NOUVEAU(0): 720x400@70Hz
[    12.215] (II) NOUVEAU(0): 640x480@60Hz
[    12.215] (II) NOUVEAU(0): 640x480@67Hz
[    12.215] (II) NOUVEAU(0): 640x480@72Hz
[    12.215] (II) NOUVEAU(0): 640x480@75Hz
[    12.215] (II) NOUVEAU(0): 800x600@56Hz
[    12.215] (II) NOUVEAU(0): 800x600@60Hz
[    12.215] (II) NOUVEAU(0): 800x600@72Hz
[    12.215] (II) NOUVEAU(0): 800x600@75Hz
[    12.215] (II) NOUVEAU(0): 832x624@75Hz
[    12.215] (II) NOUVEAU(0): 1024x768@60Hz
[    12.215] (II) NOUVEAU(0): 1024x768@70Hz
[    12.215] (II) NOUVEAU(0): 1024x768@75Hz
[    12.215] (II) NOUVEAU(0): 1280x1024@75Hz
[    12.215] (II) NOUVEAU(0): 1152x864@75Hz
[    12.215] (II) NOUVEAU(0): Manufacturer's mask: 0
[    12.215] (II) NOUVEAU(0): Supported standard timings:
[    12.215] (II) NOUVEAU(0): #0: hsize: 1280  vsize 800  refresh: 60  vid: 129
[    12.215] (II) NOUVEAU(0): #1: hsize: 1440  vsize 900  refresh: 60  vid: 149
[    12.215] (II) NOUVEAU(0): #2: hsize: 1680  vsize 1050  refresh: 60  vid: 179
[    12.215] (II) NOUVEAU(0): #3: hsize: 1280  vsize 960  refresh: 60  vid: 16513
[    12.215] (II) NOUVEAU(0): #4: hsize: 1152  vsize 864  refresh: 75  vid: 20337
[    12.215] (II) NOUVEAU(0): #5: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    12.215] (II) NOUVEAU(0): #6: hsize: 1440  vsize 900  refresh: 75  vid: 3989
[    12.215] (II) NOUVEAU(0): Supported detailed timing:
[    12.215] (II) NOUVEAU(0): clock: 148.5 MHz   Image Size:  531 x 299 mm
[    12.215] (II) NOUVEAU(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[    12.215] (II) NOUVEAU(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    12.215] (II) NOUVEAU(0): Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[    12.215] (II) NOUVEAU(0): Monitor name: SMB2430HD
[    12.216] (II) NOUVEAU(0): Serial No: 0
[    12.216] (II) NOUVEAU(0): EDID (in hex):
[    12.216] (II) NOUVEAU(0):     00ffffffffffff004c2d110734323033
[    12.216] (II) NOUVEAU(0):     0b1401030e351e782aee91a3544c9926
[    12.216] (II) NOUVEAU(0):     0f5054bfef8081009500b3008140714f
[    12.216] (II) NOUVEAU(0):     8180950f0101023a801871382d40582c
[    12.216] (II) NOUVEAU(0):     4500132b2100001e000000fd00384b1e
[    12.216] (II) NOUVEAU(0):     5111000a202020202020000000fc0053
[    12.216] (II) NOUVEAU(0):     4d423234333048440a202020000000ff
[    12.216] (II) NOUVEAU(0):     00300a20202020202020202020200003
[    12.216] (II) NOUVEAU(0): Printing probed modes for output DVI-I-1
[    12.216] (II) NOUVEAU(0): Modeline "1920x1080"x60.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[    12.216] (II) NOUVEAU(0): Modeline "1680x1050"x60.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync (65.3 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1440x900"x75.0  136.75  1440 1536 1688 1936  900 903 909 942 -hsync +vsync (70.6 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1440x900"x59.9  106.50  1440 1520 1672 1904  900 903 909 934 -hsync +vsync (55.9 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1280x800"x59.8   83.50  1280 1352 1480 1680  800 803 809 831 -hsync +vsync (49.7 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1152x864"x75.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1024x768"x70.1   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "832x624"x74.6   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "800x600"x72.2   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
[    12.216] (II) NOUVEAU(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    12.217] (II) NOUVEAU(0): Modeline "640x480"x72.8   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz e)
[    12.217] (II) NOUVEAU(0): Modeline "640x480"x66.7   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz e)
[    12.217] (II) NOUVEAU(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    12.217] (II) NOUVEAU(0): Modeline "720x400"x70.1   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz e)
[    12.284] (II) NOUVEAU(0): EDID for output TV-1
[    12.284] (II) NOUVEAU(0): Printing probed modes for output TV-1
[    12.284] (II) NOUVEAU(0): Modeline "720x576"x50.0   28.66  720 776 856 960  576 576 588 597 -hsync -vsync (29.9 kHz eP)
[    12.284] (II) NOUVEAU(0): Modeline "1024x768"x50.0   54.16  1024 1064 1200 1344  768 768 777 806 -hsync -vsync (40.3 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "800x600"x50.0   32.14  800 840 920 1040  600 600 604 618 +hsync +vsync (30.9 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "720x480"x50.0   25.20  720 752 872 960  480 480 493 525 -hsync -vsync (26.2 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "640x480"x50.0   23.10  640 672 768 880  480 480 492 525 -hsync -vsync (26.2 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "400x300"x100.0   20.10  400 432 496 640  300 300 303 314 doublescan +hsync +vsync (31.4 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "320x240"x100.0   14.73  320 344 392 560  240 240 246 263 doublescan -hsync -vsync (26.3 kHz e)
[    12.284] (II) NOUVEAU(0): Modeline "320x200"x100.0   12.32  320 344 392 560  200 200 202 220 doublescan -hsync -vsync (22.0 kHz e)
[    12.284] (II) NOUVEAU(0): Output VGA-1 disconnected
[    12.284] (II) NOUVEAU(0): Output DVI-I-1 connected
[    12.284] (II) NOUVEAU(0): Output TV-1 connected
[    12.284] (II) NOUVEAU(0): Using spanning desktop for initial modes
[    12.284] (II) NOUVEAU(0): Output DVI-I-1 using initial mode 1920x1080 +0+0
[    12.284] (II) NOUVEAU(0): Output TV-1 using initial mode 720x576 +1920+0
[    12.284] (==) NOUVEAU(0): Using gamma correction (1.0, 1.0, 1.0)
[    12.284] (--) NOUVEAU(0): Virtual size is 2640x1080 (pitch 0)
[    12.284] (**) NOUVEAU(0):  Driver mode "720x576": 28.7 MHz (scaled from 0.0 MHz), 29.9 kHz, 50.0 Hz
[    12.284] (II) NOUVEAU(0): Modeline "720x576"x50.0   28.66  720 776 856 960  576 576 588 597 -hsync -vsync (29.9 kHz eP)
[    12.284] (**) NOUVEAU(0):  Driver mode "1024x768": 54.2 MHz (scaled from 0.0 MHz), 40.3 kHz, 50.0 Hz
[    12.284] (II) NOUVEAU(0): Modeline "1024x768"x50.0   54.16  1024 1064 1200 1344  768 768 777 806 -hsync -vsync (40.3 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "800x600": 32.1 MHz (scaled from 0.0 MHz), 30.9 kHz, 50.0 Hz
[    12.284] (II) NOUVEAU(0): Modeline "800x600"x50.0   32.14  800 840 920 1040  600 600 604 618 +hsync +vsync (30.9 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "720x480": 25.2 MHz (scaled from 0.0 MHz), 26.2 kHz, 50.0 Hz
[    12.284] (II) NOUVEAU(0): Modeline "720x480"x50.0   25.20  720 752 872 960  480 480 493 525 -hsync -vsync (26.2 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "640x480": 23.1 MHz (scaled from 0.0 MHz), 26.2 kHz, 50.0 Hz
[    12.284] (II) NOUVEAU(0): Modeline "640x480"x50.0   23.10  640 672 768 880  480 480 492 525 -hsync -vsync (26.2 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "400x300": 20.1 MHz (scaled from 0.0 MHz), 31.4 kHz, 100.0 Hz (D)
[    12.284] (II) NOUVEAU(0): Modeline "400x300"x100.0   20.10  400 432 496 640  300 300 303 314 doublescan +hsync +vsync (31.4 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "320x240": 14.7 MHz (scaled from 0.0 MHz), 26.3 kHz, 100.0 Hz (D)
[    12.284] (II) NOUVEAU(0): Modeline "320x240"x100.0   14.73  320 344 392 560  240 240 246 263 doublescan -hsync -vsync (26.3 kHz e)
[    12.284] (**) NOUVEAU(0):  Driver mode "320x200": 12.3 MHz (scaled from 0.0 MHz), 22.0 kHz, 100.0 Hz (D)
[    12.284] (II) NOUVEAU(0): Modeline "320x200"x100.0   12.32  320 344 392 560  200 200 202 220 doublescan -hsync -vsync (22.0 kHz e)
[    12.284] (==) NOUVEAU(0): DPI set to (96, 96)
[    12.284] (II) Loading sub module "fb"
[    12.285] (II) LoadModule: "fb"
[    12.285] (II) Loading /usr/lib/xorg/modules/libfb.so
[    12.287] (II) Module fb: vendor="X.Org Foundation"
[    12.287]     compiled for 1.19.2, module version = 1.0.0
[    12.287]     ABI class: X.Org ANSI C Emulation, version 0.4
[    12.287] (II) Loading sub module "shadowfb"
[    12.287] (II) LoadModule: "shadowfb"
[    12.287] (II) Loading /usr/lib/xorg/modules/libshadowfb.so
[    12.288] (II) Module shadowfb: vendor="X.Org Foundation"
[    12.288]     compiled for 1.19.2, module version = 1.0.0
[    12.288]     ABI class: X.Org ANSI C Emulation, version 0.4
[    12.288] (II) UnloadModule: "modesetting"
[    12.288] (II) Unloading modesetting
[    12.288] (II) UnloadModule: "fbdev"
[    12.288] (II) Unloading fbdev
[    12.288] (II) UnloadSubModule: "fbdevhw"
[    12.288] (II) Unloading fbdevhw
[    12.288] (II) UnloadModule: "vesa"
[    12.288] (II) Unloading vesa
[    12.288] (--) Depth 24 pixmap format is 32 bpp
[    12.290] (II) NOUVEAU(0): Channel setup complete.
[    12.294] (II) NOUVEAU(0): Hardware support for Present enabled
[    12.294] (II) NOUVEAU(0): [DRI2] Setup complete
[    12.294] (II) NOUVEAU(0): [DRI2]   DRI driver: nouveau
[    12.294] (II) NOUVEAU(0): [DRI2]   VDPAU driver: nouveau
[    12.294] (II) Loading sub module "exa"
[    12.294] (II) LoadModule: "exa"
[    12.294] (II) Loading /usr/lib/xorg/modules/libexa.so
[    12.296] (II) Module exa: vendor="X.Org Foundation"
[    12.296]     compiled for 1.19.2, module version = 2.6.0
[    12.296]     ABI class: X.Org Video Driver, version 23.0
[    12.296] (II) EXA(0): Driver allocated offscreen pixmaps
[    12.296] (II) EXA(0): Driver registered support for the following operations:
[    12.296] (II)         Solid
[    12.296] (II)         Copy
[    12.296] (II)         Composite (RENDER acceleration)
[    12.296] (II)         UploadToScreen
[    12.296] (II)         DownloadFromScreen
[    12.296] (==) NOUVEAU(0): Backing store enabled
[    12.296] (==) NOUVEAU(0): Silken mouse enabled
[    12.296] (II) NOUVEAU(0): [XvMC] Associated with NV40 texture adapter.
[    12.296] (II) NOUVEAU(0): [XvMC] Extension initialized.
[    12.296] (==) NOUVEAU(0): DPMS enabled
[    12.296] (II) NOUVEAU(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    12.298] (--) RandR disabled
[    12.306] (II) SELinux: Disabled on system
[    12.944] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[    12.944] (II) AIGLX: enabled GLX_ARB_create_context
[    12.944] (II) AIGLX: enabled GLX_ARB_create_context_profile
[    12.944] (II) AIGLX: enabled GLX_EXT_create_context_es{,2}_profile
[    12.944] (II) AIGLX: enabled GLX_INTEL_swap_event
[    12.944] (II) AIGLX: enabled GLX_SGI_swap_control
[    12.944] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[    12.944] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[    12.944] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float
[    12.944] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[    12.945] (II) AIGLX: Loaded and initialized nouveau
[    12.945] (II) GLX: Initialized DRI2 GL provider for screen 0
[    12.948] (II) NOUVEAU(0): NVEnterVT is called.
[    12.948] (II) NOUVEAU(0): Setting screen physical size to 698 x 285
[    12.948] resize called 2640 1080
[    13.298] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[    13.298] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    13.298] (II) LoadModule: "libinput"
[    13.299] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[    13.332] (II) Module libinput: vendor="X.Org Foundation"
[    13.332]     compiled for 1.19.0, module version = 0.23.0
[    13.332]     Module class: X.Org XInput Driver
[    13.332]     ABI class: X.Org XInput driver, version 24.1
[    13.332] (II) Using input driver 'libinput' for 'Power Button'
[    13.332] (**) Power Button: always reports core events
[    13.332] (**) Option "Device" "/dev/input/event3"
[    13.332] (**) Option "_source" "server/udev"
[    13.333] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard
[    13.333] (II) input device 'Power Button', /dev/input/event3 is a keyboard
[    13.360] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event3"
[    13.360] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    13.360] (**) Option "xkb_model" "pc105"
[    13.360] (**) Option "xkb_layout" "pl"
[    13.405] (II) input device 'Power Button', /dev/input/event3 is tagged by udev as: Keyboard
[    13.405] (II) input device 'Power Button', /dev/input/event3 is a keyboard
[    13.406] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[    13.406] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    13.406] (II) Using input driver 'libinput' for 'Power Button'
[    13.406] (**) Power Button: always reports core events
[    13.406] (**) Option "Device" "/dev/input/event2"
[    13.406] (**) Option "_source" "server/udev"
[    13.406] (II) input device 'Power Button', /dev/input/event2 is tagged by udev as: Keyboard
[    13.406] (II) input device 'Power Button', /dev/input/event2 is a keyboard
[    13.416] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2/event2"
[    13.416] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[    13.416] (**) Option "xkb_model" "pc105"
[    13.416] (**) Option "xkb_layout" "pl"
[    13.417] (II) input device 'Power Button', /dev/input/event2 is tagged by udev as: Keyboard
[    13.417] (II) input device 'Power Button', /dev/input/event2 is a keyboard
[    13.417] (II) config/udev: Adding input device USB OPTICAL MOUSE  (/dev/input/event1)
[    13.417] (**) USB OPTICAL MOUSE : Applying InputClass "libinput pointer catchall"
[    13.417] (II) Using input driver 'libinput' for 'USB OPTICAL MOUSE '
[    13.417] (**) USB OPTICAL MOUSE : always reports core events
[    13.417] (**) Option "Device" "/dev/input/event1"
[    13.417] (**) Option "_source" "server/udev"
[    13.476] (II) input device 'USB OPTICAL MOUSE ', /dev/input/event1 is tagged by udev as: Mouse
[    13.476] (II) input device 'USB OPTICAL MOUSE ', /dev/input/event1 is a pointer caps
[    13.508] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:02.0/usb2/2-1/2-1:1.0/0003:275D:0BA6.0001/input/input1/event1"
[    13.508] (II) XINPUT: Adding extended input device "USB OPTICAL MOUSE " (type: MOUSE, id 8)
[    13.508] (**) Option "AccelerationScheme" "none"
[    13.508] (**) USB OPTICAL MOUSE : (accel) selected scheme none/0
[    13.508] (**) USB OPTICAL MOUSE : (accel) acceleration factor: 2.000
[    13.508] (**) USB OPTICAL MOUSE : (accel) acceleration threshold: 4
[    13.568] (II) input device 'USB OPTICAL MOUSE ', /dev/input/event1 is tagged by udev as: Mouse
[    13.568] (II) input device 'USB OPTICAL MOUSE ', /dev/input/event1 is a pointer caps
[    13.569] (II) config/udev: Adding input device USB OPTICAL MOUSE  (/dev/input/mouse0)
[    13.569] (II) No input driver specified, ignoring this device.
[    13.569] (II) This device may have been added with another device file.
[    13.570] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[    13.570] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[    13.570] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[    13.570] (**) AT Translated Set 2 keyboard: always reports core events
[    13.570] (**) Option "Device" "/dev/input/event0"
[    13.570] (**) Option "_source" "server/udev"
[    13.570] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard
[    13.570] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard
[    13.600] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[    13.600] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 9)
[    13.600] (**) Option "xkb_model" "pc105"
[    13.600] (**) Option "xkb_layout" "pl"
[    13.601] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is tagged by udev as: Keyboard
[    13.601] (II) input device 'AT Translated Set 2 keyboard', /dev/input/event0 is a keyboard
[    13.602] (II) config/udev: Adding input device PC Speaker (/dev/input/event4)
[    13.602] (II) No input driver specified, ignoring this device.
[    13.602] (II) This device may have been added with another device file.

nvidia-detect


Kod:

Detected NVIDIA GPUs:
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation NV43 [GeForce 6600 GT] [10de:0140] (rev a2)

Checking card:  NVIDIA Corporation NV43 [GeForce 6600 GT] (rev a2)
Your card is only supported up to the 304 legacy drivers series.
It is recommended to install the
    nvidia-legacy-304xx-driver
package.

Wiem, że muszę zainstalować sterowniki wersję 304, na forum jest stara instrukcja dla instalacji https://dug.net.pl/tekst/141/instalacja_sterownikow … a_w_debianie/
Czy dla Stretcha jest do zastosowania?

To zamrazanie systemu jest totalnie losowe; może być natychmiast po zalogowaniu a może i po kilku godzinach, jednak zawsze w końcu się zamrozi.
Mam za sobą przez te kiolka dni od instalacji pierdylion restartów. 

Po zatym co wyżej , jeszcze jeden problem się ujawnił;
instalowałem z odpiętymi pozostałymi dyskami, po podpięciu dwóch (razem 3 na komputerze debian startuje w miarę normalnie, po podpięciu 4 przy botowaniu chce z tego 4 botować i wyświetla błąd , że plików nie znalazł. Myslałem, że to coś z tym 4 dyskiem związane ale jednak nie. Mieszałem tasmami i co do dysku to jest losowe, obojętnie który dysk będzie 4 to wywala błąd botowania i co ciekawe jak w konsoli (to chyba jest konsola gruba- nie jestem pewien tego) , w każdym razie po przejściu do katalogu root  wyświetla pliki 1 partycji tego 4 dysku w zależności od tego , który dysk zostanie podpięty jako 4. Dziwne to dla mnie i nie do ogarnięcia, tym bardziej że z debianem mam doczynienia po raz pierwszy. W katalogu root mam pulpit, obrazy,wideo,pobrane,publiczny,dokumenty,muzyka,szablony, czy tak ma być? Mam osobną partycję home i swapa w systemie plików.
Komputer i Bios wykluczam , ponieważ 2 XPeki w komputerze nie mają z botowaniem i dyskami .żadnego problemu, usunięty przed instalacją dokładnie w tym samym miejscy na tym samym dysku Ubuntu 12.04 też najmniejszego problemu nie miał. Więc pozostaje na placu boju Stretch.

Jak z tymi problemami szybko się nie uporam to mimo , że mi się bardzo podoba poleci w kosmos i wróci Ubuntu.

Ostatnio edytowany przez Ainat (2018-02-14 13:00:12)

Offline

 

#4 2018-02-14 12:50:58

Jacekalex
Podobno człowiek...;)
Skąd: /dev/urandom
Zarejestrowany: 2008-01-07

Re: Debian Stretch i problemy z instalacją i po instalacji

PO pierwsze, logi się umieszcza w znacznikach CODE.

Po drugie, masz problem ze sterownikiem NOUVEAU, co widać w logu Xorga.
Spróbuj na sterowniku Nvidii.

W  wyniku

Kod:

nvidia-detect

masz napisane czarno na białym:
nvidia-legacy-304xx-driver

Więc zacznij od instalacji tego sterownika.

Czyli:

Kod:

apt install nvidia-legacy-304xx-driver nvidia-xconfig

Po zainstalowaniu sterownika musisz zrestartować komputer.

I nie strasz tu Ubuntu, bo w Ubuntu ze sterownikami jest sytuacja identyczna, jak w Debianie.
A tu największy problem jest miedzy krzesłem a klawiaturą.

Pozdro

Ostatnio edytowany przez Jacekalex (2018-02-14 13:02:40)


W demokracji każdy naród ma taką władzę, na jaką zasługuje ;)
Si vis pacem  para bellum  ;)       |       Pozdrawiam :)

Offline

 

#5 2018-02-14 13:04:51

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

nikogo niczym nie straszę.
Z Ubuntu a miałem ich kiedyś kilka nigdy, pomijając pierwsze wydania  takich problemów nie było.
Po prostu nie mam już czasu na eksperymenty, muszę mieć w tym miejscu system do pracy a nie zabawy
Jedynie o to chodzi.

Jak rozwiązać ten cyrk z dyskami, potrzebne mi są wszystkie 4?

Ostatnio edytowany przez Ainat (2018-02-14 13:11:20)

Offline

 

#6 2018-02-14 13:27:58

Jacekalex
Podobno człowiek...;)
Skąd: /dev/urandom
Zarejestrowany: 2008-01-07

Re: Debian Stretch i problemy z instalacją i po instalacji

Jakimi znowu dyskami?

Weź i zainstaluj sterownik do tej karty graficznej, to podstawa.
Potem odpal w konsoli roota polecenie:

Kod:

nvidia-xconfig

- żeby wygenerować konfigurację Xserwera, i po restarcie sterownik powinien działać.

Dysk pod Debiana wystarczy jeden, dobrze jest tylko podzielić system na kilka partycji, np partycje root, home i swap, można też zrobić osobną na /var/log.

Z resztą, jeżeli Ci tak pasuje Ubuntu, to możesz instalować Ubuntu, ale w Ubu ze sterownikami będą takie same jazdy, bo tam są identyczne sterowniki, jak w Debianie.

Ostatnio edytowany przez Jacekalex (2018-02-14 13:29:57)


W demokracji każdy naród ma taką władzę, na jaką zasługuje ;)
Si vis pacem  para bellum  ;)       |       Pozdrawiam :)

Offline

 

#7 2018-02-14 13:57:26

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

szukam źródeł dla sterownika 304 żeby dopisać do sources.list

polecenie :apt install nvidia-legacy-304xx-driver nvidia-xconfig
zwraca
E: Nie udało się odnaleźć pakietu nvidia-xconfig

a z dyskami to chyba źle zrozumiałeś; Debian jest na jednym dysku ale ja mam jeszcze inne 3 dyski i one muszą być obsługiwane przez Debiana a na razie nie ma opcji żeby zabotował z podpiętymi 4 dyskami. Opisałem to w poprzednim poście. Problemem jest to, że jak są podpięte wszystkie 4 dyski to Debian chce botować z całkiem innego dysku i się wywala, naczy nie może zabotować bo na tym dysku w ogóle niema jego plików.

Jest tak ,że jeżeli są podpięte 3 dyski to normalnie startuje ze swojego dysku i  a jak podepnę czwarty to chce startować z pierwszej partycji całkiem innego dysku i krzyczy że plików nie ma.

Ostatnio edytowany przez Ainat (2018-02-14 14:07:43)

Offline

 

#8 2018-02-14 14:18:34

zyga64
Nowy użytkownik
Zarejestrowany: 2017-02-17

Re: Debian Stretch i problemy z instalacją i po instalacji

Jeśli chodzi o sterowniki Nvidii w Debian Stretch to ja instalowałem wg. tej instrukcji: https://dug.net.pl/tekst/142/nvidia___zamkniete_sterowniki_w_debianie/,
a dokładnie wg. poniższej linijki :)

Kod:

aptitude -R install nvidia-legacy-304xx-kernel-dkms nvidia-legacy-304xx-driver nvidia-settings-legacy-304xx

Mam Quadro FX570M (ThinkPad T61p). Instalowałem jak Stretch był testing (w styczniu ubiegłego roku), od tej pory 0 problemów.

Offline

 

#9 2018-02-14 14:38:37

skullman
Użytkownik
Zarejestrowany: 2010-04-08

Re: Debian Stretch i problemy z instalacją i po instalacji

Na jakim interfejsie masz te dyski?

Offline

 

#10 2018-02-14 16:11:52

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

sata2

Offline

 

#11 2018-02-14 16:43:04

Jacekalex
Podobno człowiek...;)
Skąd: /dev/urandom
Zarejestrowany: 2008-01-07

Re: Debian Stretch i problemy z instalacją i po instalacji

szukam źródeł dla sterownika 304 żeby dopisać do sources.list

polecenie :apt install nvidia-legacy-304xx-driver nvidia-xconfig
zwraca
E: Nie udało się odnaleźć pakietu nvidia-xconfig

Hmm:

Kod:

apt-cache policy   nvidia-xconfig
nvidia-xconfig:
  Zainstalowana: (brak)
  Kandydująca:   384.111-1
  Tabela wersji:
     384.111-1 990
        990 https://deb.debian.org/debian testing/contrib amd64 Packages
        500 https://deb.debian.org/debian unstable/contrib amd64 Packages
     384.111-1~bpo9+1 100
        100 https://deb.debian.org/debian stretch-backports/contrib amd64 Packages
     375.26-1 500
        500 https://deb.debian.org/debian stable/contrib amd64 Packages

Kod:

apt-cache policy   nvidia-legacy-304xx-driver
nvidia-legacy-304xx-driver:
  Zainstalowana: (brak)
  Kandydująca:   304.137-5
  Tabela wersji:
     304.137-5 990
        990 https://deb.debian.org/debian testing/non-free amd64 Packages
        500 https://deb.debian.org/debian unstable/non-free amd64 Packages
     304.137-3~bpo9+1 100
        100 https://deb.debian.org/debian stretch-backports/non-free amd64 Packages
     304.135-2 500
        500 https://deb.debian.org/debian stable/non-free amd64 Packages

Jak widać, u Ciebie trzeba repozytoria poprawić.

Stabilne repo z mojego sources.list?

Kod:

## Strech
deb https://deb.debian.org/debian/ stable main contrib non-free
deb-src https://deb.debian.org/debian/ stable main contrib non-free


## uaktualnienia bezpieczeństwa
deb https://deb.debian.org/debian-security stable/updates main
deb-src https://deb.debian.org/debian-security stable/updates main

## często uaktualniane pakiety, np. dotyczące
deb https://deb.debian.org/debian stable-updates main contrib non-free
deb-src https://deb.debian.org/debian stable-updates main contrib non-free

#Backporty:
deb https://deb.debian.org/debian stretch-backports main contrib non-free


## przeglądarka Opera
deb http://deb.opera.com/opera/ stable non-free

## przeglądarka Google Chrome
deb  [arch=amd64] https://dl.google.com/linux/chrome/deb/ stable main

Ostatnio edytowany przez Jacekalex (2018-02-14 16:48:11)


W demokracji każdy naród ma taką władzę, na jaką zasługuje ;)
Si vis pacem  para bellum  ;)       |       Pozdrawiam :)

Offline

 

#12 2018-02-14 17:03:29

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

dodałem do source.list deb http://ftp.pl.debian.org/debian/ jessie main contrib non-free     i apt update
potem jassie zmieniłem na Stretch  i wykonałem apt update

polecenie aptitude -R install nvidia-legacy-304xx-kernel-dkms nvidia-legacy-304xx-driver nvidia-settings-legacy-304xx
zwraca basch: aptitude: nie znaleziono polecenia. apt install to samo.
Mój plik sources list na tą chwilę wygląda tak:




Kod:

# 

# deb cdrom:[Official Debian GNU/Linux Live 9.3.0 mate 2017-12-09T13:26]/ stretch main

#deb cdrom:[Official Debian GNU/Linux Live 9.3.0 mate 2017-12-09T13:26]/ stretch main
deb http://deb.debian.org/debian/ stretch main
deb-src http://deb.debian.org/debian/ stretch main
deb http://ftp.pl.debian.org/debian/ stretch main contrib non-free
deb http://security.debian.org/debian-security stretch/updates main
deb-src http://security.debian.org/debian-security stretch/updates main

# stretch-updates, previously known as 'volatile'
deb http://deb.debian.org/debian/ stretch-updates main
deb-src http://deb.debian.org/debian/ stretch-updates main
deb http://ftp.de.debian.org/debian stretch main non-free
#deb http://ftp.pl.debian.org/debian/ testing main contrib non-free
deb http://ftp.pl.debian.org/debian/ stretch main contrib non-free

Ostatnio edytowany przez Ainat (2018-02-14 17:06:09)

Offline

 

#13 2018-02-14 17:10:49

Jacekalex
Podobno człowiek...;)
Skąd: /dev/urandom
Zarejestrowany: 2008-01-07

Re: Debian Stretch i problemy z instalacją i po instalacji

Spróbuj na tych moich repo, co podałem wyżej.

Ostatnio edytowany przez Jacekalex (2018-02-14 17:11:07)


W demokracji każdy naród ma taką władzę, na jaką zasługuje ;)
Si vis pacem  para bellum  ;)       |       Pozdrawiam :)

Offline

 

#14 2018-02-14 17:21:09

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

zamieniłem wpisy w sources list i po apt update  jakichś znowu kluczy chce:

Kod:

Następujące podpisy nie mogły zostać zweryfikowane z powodu braku klucza publicznego: NO_PUBKEY D615560BA5C7FF72

Ostatnio edytowany przez Ainat (2018-02-14 18:25:05)

Offline

 

#15 2018-02-14 17:32:49

Jacekalex
Podobno człowiek...;)
Skąd: /dev/urandom
Zarejestrowany: 2008-01-07

Re: Debian Stretch i problemy z instalacją i po instalacji

Ainat napisał(-a):

zamieniłem wpisy w sources list i po apt update  jakichś znowu kluczy chce:
Następujące podpisy nie mogły zostać zweryfikowane z powodu braku klucza publicznego: NO_PUBKEY D615560BA5C7FF72

Ja to załatwiam tak:

Kod:

#!/bin/sh

if [ `id -u` -ne 0 ]; then
    echo "Tylko root może dodać klucze"
    exit 1
fi

echo -n "Aktualizacja listy pakietów (może trochę potrwać)... " && \
  apt-get update >/dev/null 2>/tmp/apt-get-update-errors && echo "OK"

if ! grep -q NO_PUBKEY /tmp/apt-get-update-errors; then
    echo "Wszystkie klucze są dodane, nie ma nic do roboty."
    rm -f /tmp/apt-get-update-errors
    exit 0
fi

for KEY in `awk '/NO_PUBKEY/ {print $NF}' /tmp/apt-get-update-errors`; do
    echo "Przetwarzanie klucza $KEY:"
    echo -n " -> pobieranie klucza z serwera... " && \
      gpg --keyserver pgp.mit.edu --recv-keys "$KEY" >/dev/null 2>&1 && \
      echo "OK" && echo -n " -> dodawanie klucza do bazy... " && \
      gpg --armor --export "$KEY" | apt-key add -
done
rm -f /tmp/apt-get-update-errors

Skrypcio sobie siedzie w systemie pod nazwą:

Kod:

/usr/local/sbin/klucze

i ma uprawnienia 755

Kod:

chmod 755 /usr/local/sbin/klucze

wywołanie, jak nie ma jakiegoś klucza?
z konsoli roota

Kod:

klucze

Pozdro

Ostatnio edytowany przez Jacekalex (2018-02-14 18:09:21)


W demokracji każdy naród ma taką władzę, na jaką zasługuje ;)
Si vis pacem  para bellum  ;)       |       Pozdrawiam :)

Offline

 

#16 2018-02-14 18:02:16

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

Kod:

.apt-get install apt-transport-https

Kod:

apt-get update

Kod:

aptitude -R install nvidia-legacy-304xx-kernel-dkms nvidia-legacy-304xx-driver nvidia-settings-legacy-304xx

bash: aptitude: nie znaleziono polecenia

Ostatnio edytowany przez Ainat (2018-02-14 18:38:39)

Offline

 

#17 2018-02-14 18:29:44

skullman
Użytkownik
Zarejestrowany: 2010-04-08

Re: Debian Stretch i problemy z instalacją i po instalacji

To zobacz, pod którym repo się pluje o klucze i albo zainstaluj albo wyhaszuj tymczasowo repo jeśli nie jest teraz istotne. Możesz sprawdzić, jakie pakiety z kluczami są dostępne:

Kod:

apt search keyring

Jak się objawia to, że system nie startuje?

Offline

 

#18 2018-02-14 18:40:57

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

klucze zrobiłem w/g przepisu

Kod:

apt-clone/stable,stable 0.4.1 all
  Script to create state bundles

debian-archive-keyring/stable,stable,now 2017.5 all [installed]
  Archiwum kluczy GnuPG dla archiwów Debiana

debian-keyring/stable,stable 2017.05.28 all
  GnuPG keys of Debian Developers and Maintainers

debian-ports-archive-keyring/stable,stable 2016.11.28 all
  GnuPG archive keys of the debian-ports archive

devscripts/stable,stable 2.17.6+deb9u1 amd64
  scripts to make the life of a Debian Package maintainer easier

emdebian-archive-keyring/stable,stable 2.2 all
  GnuPG archive keys for the emdebian repository

gambas3-gb-desktop-gnome-keyring/stable,stable 3.9.1-3 amd64
  Gambas desktop GNOME component

gir1.2-gnomekeyring-1.0/stable,stable 3.12.0-1+b2 amd64
  GNOME keyring services library - introspection data

gnome-keyring/stable,stable,now 3.20.0-3 amd64 [installed,automatic]
  Obsługa bazy kluczy GNOME (demon i narzędzia)

gpgv-static/stable,stable 2.1.18-8~deb9u1 amd64
  minimal signature verification tool (static build)

jetring/stable,stable 0.25 all
  gpg keyring maintenance using changesets

jpilot-plugins/stable,stable 1.8.2-1+b2 amd64
  Wtyczki do jpilot (środowisko palmtopa)

keyringer/stable,stable 0.5.0-2 all
  Distributed secret management using GnuPG and Git

kuvert/stable,stable 2.0.13+b1 amd64
  wrapper that encrypts or signs outgoing mail

lbdb/stable,stable 0.42.1 amd64
  Little Brother's DataBase for the mutt mail reader

leap-archive-keyring/stable,stable 2016.03.08 all
  OpenPGP archive key for the leap.se software repositories

libgnome-keyring-common/stable,stable,now 3.12.0-1 all [installed,automatic]
  GNOME keyring services library - data files

libgnome-keyring-dev/stable,stable 3.12.0-1+b2 amd64
  Pliki deweloperskie do usługi zarządzania kluczami GNOME

libgnome-keyring0/stable,stable,now 3.12.0-1+b2 amd64 [installed,automatic]
  Biblioteka usług zarządzania kluczami GNOME

libgnome-keyring0-dbg/stable,stable 3.12.0-1+b2 amd64
  Biblioteka usług zarządzania kluczami GNOME (symbole debugowania)

libgnome-keyring1.0-cil/stable,stable 1.0.0-5 amd64
  CLI library to access the GNOME Keyring daemon

libgnome-keyring1.0-cil-dev/stable,stable 1.0.0-5 amd64
  CLI library to access the GNOME Keyring daemon

libpam-gnome-keyring/stable,stable,now 3.20.0-3 amd64 [installed,automatic]
  Moduł PAM do odblokowania kluczy GNOME przy użyciu loginu

libpam-ssh-agent-auth/stable,stable 0.10.2-2 amd64
  PAM Authentication via forwarded ssh-agent

libqt5keychain1/stable,stable 0.7.0-3 amd64
  Qt API to store passwords (QT5 version)

libqtkeychain1/stable,stable 0.7.0-3 amd64
  Qt API to store passwords

libzulucrypt-plugins/stable,stable 5.0.2-2 amd64
  collection of plugins for zulucrypt

luksipc/stable,stable 0.04-2+b1 amd64
  LUKS in-place conversion tool

mercurial-extension-utils/stable,stable 1.3.1-1 all
  Contains functions for writing Mercurial extensions.

mercurial-keyring/stable,stable 1.1.7-1 all
  Mercurial Keyring Extension

monodoc-gnome-keyring-manual/stable,stable 1.0.0-5 all
  CLI library to access the GNOME Keyring daemon - manual

mpop-gnome/stable,stable 1.2.6-1 amd64
  POP3 mail retriever - with GNOME keyring support

msmtp-gnome/stable,stable 1.6.6-1 amd64
  light SMTP client with support for server profiles - with GNOME keyring support

network-manager-gnome/stable,stable,now 1.4.4-1 amd64 [installed,automatic]
  Szkielet zarządzania siecią (nakładka do GNOME)

neurodebian-archive-keyring/stable,stable 0.37.6 all
  neuroscience-oriented distribution - GnuPG archive keys

nss-passwords/stable,stable 0.2-2+b1 amd64
  read passwords from a Mozilla keyring

parcimonie/stable,stable 0.10.2-4 all
  privacy-friendly helper to refresh a GnuPG keyring

pidgin-gnome-keyring/stable,stable 2.0-1 amd64
  integrates pidgin (and libpurple) with the system keyring

pidgin-gnome-keyring-dbg/stable,stable 2.0-1 amd64
  debugging symbols for pidgin-gnome-keyring

pius/stable,stable 2.2.3-1 all
  Tools to help before and after key-signing parties

pkg-mozilla-archive-keyring/stable,stable 1.1 all
  GnuPG archive keys for the Debian Mozilla team package repository

python-gnomekeyring/stable,stable 2.32.0+dfsg-3 amd64
  Wiązania Pythona dla biblioteki GNOME keyring

python-gpg/stable,stable 1.8.0-3+b2 amd64
  Python interface to the GPGME GnuPG encryption library (Python 2)

python-keyring/stable,stable 10.1-1 all
  store and access your passwords safely

python-keyrings.alt/stable,stable 1.3-1 all
  alternate backend implementations for python-keyring

python-secretstorage/stable,stable 2.3.1-2 all
  Python module for storing secrets - Python 2.x version

python-secretstorage-doc/stable,stable 2.3.1-2 all
  Python module for storing secrets - documentation

python3-gpg/stable,stable 1.8.0-3+b2 amd64
  Python interface to the GPGME GnuPG encryption library (Python 3)

python3-keyring/stable,stable 10.1-1 all
  store and access your passwords safely - Python 3 version of the package

python3-keyrings.alt/stable,stable 1.3-1 all
  alternate backend implementations for python3-keyring

python3-secretstorage/stable,stable 2.3.1-2 all
  Python module for storing secrets - Python 3.x version

qt5keychain-dev/stable,stable 0.7.0-3 amd64
  Development files for qtkeychain (QT5 version)

qtkeychain-dev/stable,stable 0.7.0-3 amd64
  Development files for qtkeychain

remmina-plugin-gnome/stretch-backports 1.2.0-rcgit.24-2~bpo9+1 amd64
  GNOME plugin for remmina remote desktop client

remmina-plugin-secret/stretch-backports 1.2.0-rcgit.26+dfsg-1~bpo9+1 amd64
  Secret plugin for Remmina

signing-party/stable,stable 2.5-1 amd64
  Various OpenPGP related tools

ubuntu-archive-keyring/stable,stable 2016.05.13-1 all
  GnuPG keys of the Ubuntu archive

webauth-utils/stable,stable 4.7.0-4 amd64
  Command-line utilities for WebAuth authentication

xul-ext-gnome-keyring/stable,stable 0.12-1 all
  Store mozilla passwords in GNOME Keyring

w konsoli wszystkie na zielono

Ostatnio edytowany przez Ainat (2018-02-14 18:41:57)

Offline

 

#19 2018-02-14 18:48:58

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

jeżeli chodzi o sprawę z dyskami to wywala czarny ekran z informacją ,że nie znalazł plików startowych i można jedynie pisać w konsoli albo wycofać się do kolejnego restartu. Opsałem szczegółowo wszystko wyżej

Offline

 

#20 2018-02-14 18:50:00

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

tego

Kod:

 aptitude -R install nvidia-legacy-304xx-kernel-dkms nvidia-legacy-304xx-driver nvidia-settings-legacy-304xx

nie mozna zainstalować , dlaczemu?

Ostatnio edytowany przez Ainat (2018-02-14 18:50:41)

Offline

 

#21 2018-02-14 18:58:01

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

Kod:

https://wiki.debian.org/NvidiaGraphicsDrivers#Version_304.135_.28legacy_GPUs.29

W/g tego poradnika zainstalowało się normalnie , zobaczymy po restarcie


Po restarcie polecenie

Kod:

nvidia-detect

Detected NVIDIA GPUs:
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation NV43 [GeForce 6600 GT] [10de:0140] (rev a2)

Checking card:  NVIDIA Corporation NV43 [GeForce 6600 GT] (rev a2)
Your card is only supported up to the 304 legacy drivers series.
It is recommended to install the
    nvidia-legacy-304xx-driver

Polecenie

Kod:

nvidia-xconfig

odpowiada

Kod:

bash: nvidia-xconfig: nie znaleziono polecenia

Wyczerpują się pokłady mojej osobistej cierpliwości  a jestem wyjątkowo spokojny człowiek

Ostatnio edytowany przez Ainat (2018-02-14 19:10:40)

Offline

 

#22 2018-02-14 19:02:22

andreq
Członek DUG
Skąd: Nisko
Zarejestrowany: 2005-01-11

Re: Debian Stretch i problemy z instalacją i po instalacji

Co do dysków: ustaw w biosie odpowiadającą Ci kolejność bootowania

Offline

 

#23 2018-02-14 19:13:24

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

nic to nie daje , ja na płycie mam takie boot menu,że mogę sobie wybierać z którego ma startować. Problem jest w botloaderze debiana a nie w moim kompie.
Tak jak by jego możliwości kończyły się na obsłudze 3dysków.

Ostatnio edytowany przez Ainat (2018-02-14 19:32:43)

Offline

 

#24 2018-02-14 19:15:17

Ainat
Użytkownik
Zarejestrowany: 2018-01-05

Re: Debian Stretch i problemy z instalacją i po instalacji

No  i się jednak zainstalowały , mam zakładce Administracja panel Nvidi . Hura!!! po tygodniu męczarni. Teraz została do rozwiązania sprawa dysków

Ostatnio edytowany przez Ainat (2018-02-14 19:33:03)

Offline

 

#25 2018-02-14 19:35:51

andreq
Członek DUG
Skąd: Nisko
Zarejestrowany: 2005-01-11

Re: Debian Stretch i problemy z instalacją i po instalacji

Może i problem jest w bootloaderze, ale jak nie podasz komunikatu/logów to nikt nie domyśli się co nie działa. Wklej co wypisuje jak masz podpięte wszystkie dyski. Chociaż jak system startuje z jednym, to powinien startować przy wszystkich jak ten z debianem będzie posdpięty do portu sata1

Ostatnio edytowany przez andreq (2018-02-14 19:37:48)

Offline

 

Stopka forum

Powered by PunBB
© Copyright 2002–2005 Rickard Andersson
Możesz wyłączyć AdBlock — tu nie ma reklam ;-)