Forum Debian Users Gang

...
[    7.524838] scsi 3:0:0:0: Direct-Access     WD       5000AAC External 1.65 PQ: 0 ANSI: 4
[    7.528429] sd 3:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    7.529302] sd 3:0:0:0: [sdc] Write Protect is off
[    7.529311] sd 3:0:0:0: [sdc] Mode Sense: 21 00 00 00
[    7.529317] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[    7.531039] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[    7.531095]  sdc: sdc1 sdc2 sdc3 < sdc5 >
[   14.341805] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[   14.341866] sd 3:0:0:0: [sdc] Attached SCSI disk
[   14.733068] PM: Starting manual resume from disk
[   14.733081] PM: Resume from partition 8:37
[   14.733085] PM: Checking hibernation image.
[   14.733714] PM: Error -22 checking image file
[   14.733720] PM: Resume from disk failed.
[   16.385783] sd 2:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[   16.387520] sd 2:0:0:0: [sdb] Write Protect is off
[   16.387529] sd 2:0:0:0: [sdb] Mode Sense: 1c 00 00 00
[   16.387535] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[   16.391142] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[   16.391191]  sdb: sdb1
[   16.621963] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[   16.622023] sd 2:0:0:0: [sdb] Attached SCSI disk
[   16.669195] EXT3-fs: INFO: recovery required on readonly filesystem.
[   16.669204] EXT3-fs: write access will be enabled during recovery.
[   22.071054] kjournald starting.  Commit interval 5 seconds
[   22.071096] EXT3-fs: recovery complete.
[   22.072086] EXT3-fs: mounted filesystem with ordered data mode.
[   23.591683] udev[403]: starting version 164
[   24.265542] input: PC Speaker as /devices/platform/pcspkr/input/input0
[   24.265846] processor LNXCPU:00: registered as cooling_device1
[   24.276551] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[   24.276591] ACPI: Power Button [PWRB]
[   24.277036] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[   24.277054] ACPI: Sleep Button [FUTS]
[   24.277246] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[   24.277255] ACPI: Power Button [PWRF]
[   24.391958] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   24.463177] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x10c0
[   24.482491] parport_pc 00:08: reported by Plug and Play ACPI
[   24.482555] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[   24.790928] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   25.189535] Error: Driver 'pcspkr' is already registered, aborting...
[   25.544585] Intel ICH 0000:00:02.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[   25.868033] intel8x0_measure_ac97_clock: measured 53718 usecs (2584 samples)
[   25.868042] intel8x0: clocking to 48000
[   25.922443] usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0027
[   25.922505] usbcore: registered new interface driver usblp
[   26.974545] Adding 753656k swap on /dev/sdc5.  Priority:-1 extents:1 across:753656k 
[   27.385112] EXT3 FS on sdc2, internal journal
[   27.598647] loop: module loaded
[   28.384717] kjournald starting.  Commit interval 5 seconds
[   28.401507] EXT3 FS on sda5, internal journal
[   28.401520] EXT3-fs: mounted filesystem with ordered data mode.
[   28.554044] fuse init (API version 7.13)
[   31.170053] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[   33.000695] lp0: using parport0 (interrupt-driven).
[   33.057983] ppdev: user-space parallel port driver
[   35.839112] usb 3-1: usbfs: interface 0 claimed by usblp while 'usb' sets config #1
...