Forum Debian Users Gang

# cat /etc/apache2/vhosts.d/00_default_ssl_vhost.conf
<IfDefine SSL>
<IfDefine SSL_DEFAULT_VHOST>
<IfModule ssl_module>
# see bug #178966 why this is in here

# When we also provide SSL we have to listen to the HTTPS port
# Note: Configurations that use IPv6 but not IPv4-mapped addresses need two
# Listen directives: "Listen [::]:443" and "Listen 0.0.0.0:443"
Listen 443
NameVirtualHost *:443

<VirtualHost _default_:443>
        ServerName localhost
        Include /etc/apache2/vhosts.d/default_vhost.include
        ErrorLog /var/log/apache2/ssl_error_log

        <IfModule log_config_module>
                TransferLog /var/log/apache2/ssl_access_log
        </IfModule>

        ## SSL Engine Switch:
        # Enable/Disable SSL for this virtual host.
        SSLEngine on

        ## SSL Cipher Suite:
        # List the ciphers that the client is permitted to negotiate.
        # See the mod_ssl documentation for a complete list.
        SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL

        ## Server Certificate:
        # Point SSLCertificateFile at a PEM encoded certificate. If the certificate
        # is encrypted, then you will be prompted for a pass phrase. Note that a
        # kill -HUP will prompt again. Keep in mind that if you have both an RSA
        # and a DSA certificate you can configure both in parallel (to also allow
        # the use of DSA ciphers, etc.)
        SSLCertificateFile /etc/ssl/apache2/server.crt

        ## Server Private Key:
        # If the key is not combined with the certificate, use this directive to
        # point at the key file. Keep in mind that if you've both a RSA and a DSA
        # private key you can configure both in parallel (to also allow the use of
        # DSA ciphers, etc.)
        SSLCertificateKeyFile /etc/ssl/apache2/server.key

        ## Server Certificate Chain:
        # Point SSLCertificateChainFile at a file containing the concatenation of
        # PEM encoded CA certificates which form the certificate chain for the
        # server certificate. Alternatively the referenced file can be the same as
        # SSLCertificateFile when the CA certificates are directly appended to the
        # server certificate for convinience.
        #SSLCertificateChainFile /etc/ssl/apache2/ca.crt

        ## Certificate Authority (CA):
        # Set the CA certificate verification path where to find CA certificates
        # for client authentication or alternatively one huge file containing all
        # of them (file must be PEM encoded).
        # Note: Inside SSLCACertificatePath you need hash symlinks to point to the
        # certificate files. Use the provided Makefile to update the hash symlinks
        # after changes.
        #SSLCACertificatePath /etc/ssl/apache2/ssl.crt
        #SSLCACertificateFile /etc/ssl/apache2/ca-bundle.crt

        ## Certificate Revocation Lists (CRL):
        # Set the CA revocation path where to find CA CRLs for client authentication
        # or alternatively one huge file containing all of them (file must be PEM
        # encoded).
        # Note: Inside SSLCARevocationPath you need hash symlinks to point to the
        # certificate files. Use the provided Makefile to update the hash symlinks
        # after changes.
        #SSLCARevocationPath /etc/ssl/apache2/ssl.crl
        #SSLCARevocationFile /etc/ssl/apache2/ca-bundle.crl

        ## Client Authentication (Type):
        # Client certificate verification type and depth. Types are none, optional,
        # require and optional_no_ca. Depth is a number which specifies how deeply
        # to verify the certificate issuer chain before deciding the certificate is
        # not valid.
        #SSLVerifyClient require
        #SSLVerifyDepth  10

        ## Access Control:
        # With SSLRequire you can do per-directory access control based on arbitrary
        # complex boolean expressions containing server variable checks and other
        # lookup directives. The syntax is a mixture between C and Perl. See the
        # mod_ssl documentation for more details.
        #<Location />
        #       #SSLRequire (    %{SSL_CIPHER} !~ m/^(EXP|NULL)/ \
        #       and %{SSL_CLIENT_S_DN_O} eq "Snake Oil, Ltd." \
        #       and %{SSL_CLIENT_S_DN_OU} in {"Staff", "CA", "Dev"} \
        #       and %{TIME_WDAY} >= 1 and %{TIME_WDAY} <= 5 \
        #       and %{TIME_HOUR} >= 8 and %{TIME_HOUR} <= 20       ) \
        #       or %{REMOTE_ADDR} =~ m/^192\.76\.162\.[0-9]+$/
        #</Location>

        ## SSL Engine Options:
        # Set various options for the SSL engine.

        ## FakeBasicAuth:
        # Translate the client X.509 into a Basic Authorisation. This means that the
        # standard Auth/DBMAuth methods can be used for access control. The user
        # name is the `one line' version of the client's X.509 certificate.
        # Note that no password is obtained from the user. Every entry in the user
        # file needs this password: `xxj31ZMTZzkVA'.

        ## ExportCertData:
        # This exports two additional environment variables: SSL_CLIENT_CERT and
        # SSL_SERVER_CERT. These contain the PEM-encoded certificates of the server
        # (always existing) and the client (only existing when client
        # authentication is used). This can be used to import the certificates into
        # CGI scripts.

        ## StdEnvVars:
        # This exports the standard SSL/TLS related `SSL_*' environment variables.
        # Per default this exportation is switched off for performance reasons,
        # because the extraction step is an expensive operation and is usually
        # useless for serving static content. So one usually enables the exportation
        # for CGI and SSI requests only.

        ## StrictRequire:
        # This denies access when "SSLRequireSSL" or "SSLRequire" applied even under
        # a "Satisfy any" situation, i.e. when it applies access is denied and no
        # other module can change it.

        ## OptRenegotiate:
        # This enables optimized SSL connection renegotiation handling when SSL
        # directives are used in per-directory context.
        #SSLOptions +FakeBasicAuth +ExportCertData +StrictRequire
        <FilesMatch "\.(cgi|shtml|phtml|php)$">
                SSLOptions +StdEnvVars
        </FilesMatch>

        <Directory "/var/www/localhost/cgi-bin">
                SSLOptions +StdEnvVars
        </Directory>

        ## SSL Protocol Adjustments:
        # The safe and default but still SSL/TLS standard compliant shutdown
        # approach is that mod_ssl sends the close notify alert but doesn't wait
        # for the close notify alert from client. When you need a different
        # shutdown approach you can use one of the following variables:

        ## ssl-unclean-shutdown:
        # This forces an unclean shutdown when the connection is closed, i.e. no
        # SSL close notify alert is send or allowed to received.  This violates the
        # SSL/TLS standard but is needed for some brain-dead browsers. Use this when
        # you receive I/O errors because of the standard approach where mod_ssl
        # sends the close notify alert.

        ## ssl-accurate-shutdown:
        # This forces an accurate shutdown when the connection is closed, i.e. a
        # SSL close notify alert is send and mod_ssl waits for the close notify
        # alert of the client. This is 100% SSL/TLS standard compliant, but in
        # practice often causes hanging connections with brain-dead browsers. Use
        # this only for browsers where you know that their SSL implementation works
        # correctly.
        # Notice: Most problems of broken clients are also related to the HTTP
        # keep-alive facility, so you usually additionally want to disable
        # keep-alive for those clients, too. Use variable "nokeepalive" for this.
        # Similarly, one has to force some clients to use HTTP/1.0 to workaround
        # their broken HTTP/1.1 implementation. Use variables "downgrade-1.0" and
        # "force-response-1.0" for this.
        <IfModule setenvif_module>
                BrowserMatch ".*MSIE.*" \
                        nokeepalive ssl-unclean-shutdown \
                        downgrade-1.0 force-response-1.0
        </IfModule>

        ## Per-Server Logging:
        # The home of a custom SSL log file. Use this when you want a compact
        # non-error SSL logfile on a virtual host basis.
        <IfModule log_config_module>
                CustomLog /var/log/apache2/ssl_request_log \
                        "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b"
        </IfModule>
</VirtualHost>

<VirtualHost *:443>
        SSLEngine on
        SSLCertificateFile /etc/ssl/apache2/admin.crt
        SSLCertificateKeyFile /etc/ssl/apache2/admin.key

        ServerName www1.admin.server

        SSLOptions StrictRequire
        SSLProtocol all -SSLv2

        DocumentRoot /var/www/localhost/htdocs/phpmyadmin
        <Directory /var/www/localhost/htdocs/phpmyadmin>
                Options Indexes FollowSymLinks MultiViews
                AllowOverride All
                SSLRequireSSL
                Order Allow,Deny
                Allow from All
        </Directory>
</VirtualHost>

</IfModule>
</IfDefine>
</IfDefine>

<VirtualHost *:443>
SSLEngine on
SSLCertificateFile /etc/ssl/apache2/admin.crt
SSLCertificateKeyFile /etc/ssl/apache2/admin.key

ServerName www1.svn.server

SSLOptions StrictRequire
SSLProtocol all -SSLv2

DocumentRoot /var/www/localhost/htdocs/websvn

<Location />
       AuthType Basic
       AuthName "Subversion repository"
       AuthUserFile /var/svn/conf/svnusers
       #AuthzSVNAccessFile /var/svn/conf/authz
       Require valid-user
       SSLRequireSSL
       Order Allow,Deny
       Allow from All
</Location>

<Location /svn>
       DAV svn
       SVNParentPath /var/svn/
       AuthType Basic
       AuthName "Subversion repository"
       AuthUserFile /var/svn/conf/svnusers
       #AuthzSVNAccessFile /var/svn/conf/authz
       Require valid-user
       SSLRequireSSL
       Order Allow,Deny
       Allow from All
</Location>
</VirtualHost>

# vim: ts=4 filetype=apache