Forum Debian Users Gang

# sensors-detect revision 5861 (2010-09-21 17:21:05 +0200)
# System: FUJITSU PRIMERGY RX100 S6
# Board: FUJITSU D2863

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no):
Module cpuid loaded successfully.
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
Intel digital thermal sensor...                             Success!
    (driver `coretemp')
Intel AMB FB-DIMM thermal sensor...                         No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no):
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No

Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no):
Found `IPMI BMC KCS' at 0xca2...                            Success!
    (confidence 8, driver `ipmisensors')

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (YES/no):
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no):
Using driver `i2c-i801' for device 0000:00:1f.3: Intel 3400/5 Series (PCH)
Module i2c-dev loaded successfully.

Next adapter: SMBus I801 adapter at 1840 (i2c-0)
Do you want to scan it? (YES/no/selectively):
Client found at address 0x18
Handled by driver `adm1021' (already loaded), chip type `max1617'
Client found at address 0x50
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 No
Probing for `EDID EEPROM'...                                No

Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `adm1021':
  * Bus `SMBus I801 adapter at 1840'
    Busdriver `i2c_i801', I2C address 0x18
    Chip `max1617' (confidence: 6)

Driver `coretemp':
  * Chip `Intel digital thermal sensor' (confidence: 9)

Driver `ipmisensors':
  * ISA bus, address 0xca2
    Chip `IPMI BMC KCS' (confidence: 8)

Warning: the required module ipmisensors is not currently installed
on your system. If it is built into the kernel then it's OK.
Otherwise, check http://www.lm-sensors.org/wiki/Devices for
driver availability.

To load everything that is needed, add this to /etc/modules:
#----cut here----
# Adapter drivers
ipmi-si
# Chip drivers
adm1021
coretemp
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!

Do you want to add these lines automatically to /etc/modules? (yes/NO)

Unloading i2c-dev... OK
Unloading cpuid... OK

Adapter: ACPI interface
power1:      51.00 W  (interval =  60.00 s)

max1617-i2c-0-18
Adapter: SMBus I801 adapter at 1840
temp1:        +0.0°C  (low  = +16.0°C, high = +65.0°C)
temp2:        +2.0°C  (low  =  +1.0°C, high =  +3.0°C)

Loading configuration from /etc/fancontrol ...
Error: Can't read configuration file

This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.

We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.

/usr/sbin/pwmconfig: There are no pwm-capable sensor modules installed