Nie jesteś zalogowany.
Jeśli nie posiadasz konta, zarejestruj je już teraz! Pozwoli Ci ono w pełni korzystać z naszego serwisu. Spamerom dziękujemy!

Ogłoszenie

Prosimy o pomoc dla małej Julki — przekaż 1% podatku na Fundacji Dzieciom zdazyć z Pomocą.
Więcej informacji na dug.net.pl/pomagamy/.

#1  2021-10-10 12:54:29

  wobo - Użytkownik

wobo
Użytkownik
Skąd: Warszawa
Zarejestrowany: 2013-10-16

802.11ax (WIFI 6) Intel Cannon Point-LP CNVi [Wireless-AC] (rev 30)

Cześć

Mam pytanie odnośnie sprawdzenia obsługi tegoż standardu przez kartę w moim laptopie

Jako że na OpenWrt  mam dostępny ten standard oraz łatwość jego włączenia jest jest trywialna, jak widać poniżej

Kod:

root@AP:~# uci show wireless | grep HE80
root@AP:~# uci set wireless.radio1.htmode='HE80'
root@AP:~# uci show wireless | grep HE80
wireless.radio1.htmode='HE80'
root@AP:~# /etc/init.d/network restart

Android bez problemu informuje na ikonce WIFI o połączeniu z siecią kat 6 a z Debianem nie mogę sobie poradzić.
Mam na laptopie systemd-netowrkd, nie posiadam graficznego managera np. nm. Może tam też jest ikonka ;)

Teraz kilka szczegółów

Typ karty Cannon Point-LP CNVi [Wireless-AC]

Kod:

00:14.3 Network controller: Intel Corporation Cannon Point-LP CNVi [Wireless-AC] (rev 30)
        DeviceName: WLAN
        Subsystem: Intel Corporation Cannon Point-LP CNVi [Wireless-AC]
        Flags: bus master, fast devsel, latency 0, IRQ 16, IOMMU group 6
        Memory at b431c000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [c8] Power Management version 3
        Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
        Capabilities: [40] Express Root Complex Integrated Endpoint, MSI 00
        Capabilities: [80] MSI-X: Enable+ Count=16 Masked-
        Capabilities: [100] Null
        Capabilities: [14c] Latency Tolerance Reporting
        Capabilities: [164] Vendor Specific Information: ID=0010 Rev=0 Len=014 <?>
        Kernel driver in use: iwlwifi
        Kernel modules: iwlwifi

Sprawdzałem na Intelu, i znalazłem taki artykuł https://www.intel.com/content/www/us/en/support/art … wireless.html
Teoretycznie powinienem obsługiwać standard 80211ax...
Ale trudno jest ustalić jaki konkretnie mam wlutowany moduł CRF M2 powiązany z CNVi.
Więc tego nie jestem pewien.

I teraz sprawdzam wireless-tools iw w poszukiwanu opcji HE.. ale niestety nie znajduję takiej.

Kod:

# iw phy | grep HE
        Device supports SAE with AUTHENTICATE command

A poniżej cały wynik:

Kod:

# iw phy
Wiphy phy0
        wiphy index: 0
        max # scan SSIDs: 20
        max scan IEs length: 422 bytes
        max # sched scan SSIDs: 20
        max # match sets: 11
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Device supports RSN-IBSS.
        Device supports AP-side u-APSD.
        Device supports T-DLS.
        Supported Ciphers:
                * WEP40 (00-0f-ac:1)
                * WEP104 (00-0f-ac:5)
                * TKIP (00-0f-ac:2)
                * CCMP-128 (00-0f-ac:4)
                * GCMP-128 (00-0f-ac:8)
                * GCMP-256 (00-0f-ac:9)
                * CMAC (00-0f-ac:6)
                * GMAC-128 (00-0f-ac:11)
                * GMAC-256 (00-0f-ac:12)
        Available Antennas: TX 0x3 RX 0x3
        Configured Antennas: TX 0x3 RX 0x3
        Supported interface modes:
                 * IBSS
                 * managed
                 * AP
                 * AP/VLAN
                 * monitor
                 * P2P-client
                 * P2P-GO
                 * P2P-device
        Band 1:
                Capabilities: 0x19ef
                        RX LDPC
                        HT20/HT40
                        SM Power Save disabled
                        RX HT20 SGI
                        RX HT40 SGI
                        TX STBC
                        RX STBC 1-stream
                        Max AMSDU length: 7935 bytes
                        DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: 4 usec (0x05)
                HT Max RX data rate: 300 Mbps
                HT TX/RX MCS rate indexes supported: 0-15
                Bitrates (non-HT):
                        * 1.0 Mbps
                        * 2.0 Mbps (short preamble supported)
                        * 5.5 Mbps (short preamble supported)
                        * 11.0 Mbps (short preamble supported)
                        * 6.0 Mbps
                        * 9.0 Mbps
                        * 12.0 Mbps
                        * 18.0 Mbps
                        * 24.0 Mbps
                        * 36.0 Mbps
                        * 48.0 Mbps
                        * 54.0 Mbps
                Frequencies:
                        * 2412 MHz [1] (22.0 dBm)
                        * 2417 MHz [2] (22.0 dBm)
                        * 2422 MHz [3] (22.0 dBm)
                        * 2427 MHz [4] (22.0 dBm)
                        * 2432 MHz [5] (22.0 dBm)
                        * 2437 MHz [6] (22.0 dBm)
                        * 2442 MHz [7] (22.0 dBm)
                        * 2447 MHz [8] (22.0 dBm)
                        * 2452 MHz [9] (22.0 dBm)
                        * 2457 MHz [10] (22.0 dBm)
                        * 2462 MHz [11] (22.0 dBm)
                        * 2467 MHz [12] (22.0 dBm)
                        * 2472 MHz [13] (22.0 dBm)
                        * 2484 MHz [14] (disabled)
        Band 2:
                Capabilities: 0x19ef
                        RX LDPC
                        HT20/HT40
                        SM Power Save disabled
                        RX HT20 SGI
                        RX HT40 SGI
                        TX STBC
                        RX STBC 1-stream
                        Max AMSDU length: 7935 bytes
                        DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: 4 usec (0x05)
                HT Max RX data rate: 300 Mbps
                HT TX/RX MCS rate indexes supported: 0-15
                VHT Capabilities (0x039071f6):
                        Max MPDU length: 11454
                        Supported Channel Width: 160 MHz
                        RX LDPC
                        short GI (80 MHz)
                        short GI (160/80+80 MHz)
                        TX STBC
                        SU Beamformee
                        MU Beamformee
                VHT RX MCS set:
                        1 streams: MCS 0-9
                        2 streams: MCS 0-9
                        3 streams: not supported
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT RX highest supported: 0 Mbps
                VHT TX MCS set:
                        1 streams: MCS 0-9
                        2 streams: MCS 0-9
                        3 streams: not supported
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT TX highest supported: 0 Mbps
                Bitrates (non-HT):
                        * 6.0 Mbps
                        * 9.0 Mbps
                        * 12.0 Mbps
                        * 18.0 Mbps
                        * 24.0 Mbps
                        * 36.0 Mbps
                        * 48.0 Mbps
                        * 54.0 Mbps
                Frequencies:
                        * 5180 MHz [36] (22.0 dBm) (no IR)
                        * 5200 MHz [40] (22.0 dBm) (no IR)
                        * 5220 MHz [44] (22.0 dBm) (no IR)
                        * 5240 MHz [48] (22.0 dBm) (no IR)
                        * 5260 MHz [52] (22.0 dBm) (no IR, radar detection)
                        * 5280 MHz [56] (22.0 dBm) (no IR, radar detection)
                        * 5300 MHz [60] (22.0 dBm) (no IR, radar detection)
                        * 5320 MHz [64] (22.0 dBm) (no IR, radar detection)
                        * 5340 MHz [68] (disabled)
                        * 5360 MHz [72] (disabled)
                        * 5380 MHz [76] (disabled)
                        * 5400 MHz [80] (disabled)
                        * 5420 MHz [84] (disabled)
                        * 5440 MHz [88] (disabled)
                        * 5460 MHz [92] (disabled)
                        * 5480 MHz [96] (disabled)
                        * 5500 MHz [100] (22.0 dBm) (no IR, radar detection)
                        * 5520 MHz [104] (22.0 dBm) (no IR, radar detection)
                        * 5540 MHz [108] (22.0 dBm) (no IR, radar detection)
                        * 5560 MHz [112] (22.0 dBm) (no IR, radar detection)
                        * 5580 MHz [116] (22.0 dBm) (no IR, radar detection)
                        * 5600 MHz [120] (22.0 dBm) (no IR, radar detection)
                        * 5620 MHz [124] (22.0 dBm) (no IR, radar detection)
                        * 5640 MHz [128] (22.0 dBm) (no IR, radar detection)
                        * 5660 MHz [132] (22.0 dBm) (no IR, radar detection)
                        * 5680 MHz [136] (22.0 dBm) (no IR, radar detection)
                        * 5700 MHz [140] (22.0 dBm) (no IR, radar detection)
                        * 5720 MHz [144] (22.0 dBm) (no IR, radar detection)
                        * 5745 MHz [149] (22.0 dBm)
                        * 5765 MHz [153] (22.0 dBm)
                        * 5785 MHz [157] (22.0 dBm)
                        * 5805 MHz [161] (22.0 dBm)
                        * 5825 MHz [165] (22.0 dBm)
                        * 5845 MHz [169] (disabled)
                        * 5865 MHz [173] (disabled)
                        * 5885 MHz [177] (disabled)
                        * 5905 MHz [181] (disabled)
        Supported commands:
                 * new_interface
                 * set_interface
                 * new_key
                 * start_ap
                 * new_station
                 * new_mpath
                 * set_mesh_config
                 * set_bss
                 * authenticate
                 * associate
                 * deauthenticate
                 * disassociate
                 * join_ibss
                 * join_mesh
                 * remain_on_channel
                 * set_tx_bitrate_mask
                 * frame
                 * frame_wait_cancel
                 * set_wiphy_netns
                 * set_channel
                 * set_wds_peer
                 * tdls_mgmt
                 * tdls_oper
                 * start_sched_scan
                 * probe_client
                 * set_noack_map
                 * register_beacons
                 * start_p2p_device
                 * set_mcast_rate
                 * connect
                 * disconnect
                 * channel_switch
                 * set_qos_map
                 * add_tx_ts
                 * set_multicast_to_unicast
        WoWLAN support:
                 * wake up on disconnect
                 * wake up on magic packet
                 * wake up on pattern match, up to 20 patterns of 16-128 bytes,
                   maximum packet offset 0 bytes
                 * can do GTK rekeying
                 * wake up on GTK rekey failure
                 * wake up on EAP identity request
                 * wake up on 4-way handshake
                 * wake up on rfkill release
                 * wake up on network detection, up to 11 match sets
        software interface modes (can always be added):
                 * AP/VLAN
                 * monitor
        valid interface combinations:
                 * #{ managed } <= 1, #{ AP, P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
                   total <= 3, #channels <= 2
        HT Capability overrides:
                 * MCS: ff ff ff ff ff ff ff ff ff ff
                 * maximum A-MSDU length
                 * supported channel width
                 * short GI for 40 MHz
                 * max A-MPDU length exponent
                 * min MPDU start spacing
        Device supports TX status socket option.
        Device supports HT-IBSS.
        Device supports SAE with AUTHENTICATE command
        Device supports low priority scan.
        Device supports scan flush.
        Device supports per-vif TX power setting
        P2P GO supports CT window setting
        P2P GO supports opportunistic powersave setting
        Driver supports full state transitions for AP/GO clients
        Driver supports a userspace MPM
        Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
        Device adds DS IE to probe requests
        Device can update TPC Report IE
        Device supports static SMPS
        Device supports dynamic SMPS
        Device supports WMM-AC admission (TSPECs)
        Device supports configuring vdev MAC-addr on create.
        Device supports randomizing MAC-addr in scans.
        Device supports randomizing MAC-addr in sched scans.
        Device supports randomizing MAC-addr in net-detect scans.
        max # scan plans: 2
        max scan plan interval: 65535
        max scan plan iterations: 254
        Supported TX frame types:
                 * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
                 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
        Supported RX frame types:
                 * IBSS: 0x40 0xb0 0xc0 0xd0
                 * managed: 0x40 0xb0 0xd0
                 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
                 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
                 * mesh point: 0xb0 0xc0 0xd0
                 * P2P-client: 0x40 0xd0
                 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
                 * P2P-device: 0x40 0xd0
        Supported extended features:
                * [ VHT_IBSS ]: VHT-IBSS
                * [ RRM ]: RRM
                * [ MU_MIMO_AIR_SNIFFER ]: MU-MIMO sniffer
                * [ SCAN_START_TIME ]: scan start timestamp
                * [ BSS_PARENT_TSF ]: BSS last beacon/probe TSF
                * [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
                * [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
                * [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
                * [ EXT_KEY_ID ]: Extended Key ID support
                * [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
                * [ DEL_IBSS_STA ]: deletion of IBSS station support
                * [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
                * [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support

Jak to sprawdzić i jak ewentualnie włączyć?

Pozdrowienia
wobo

Offline

 

#2  2021-10-10 14:33:22

  fnmirk - Redaktor

fnmirk
Redaktor
Zarejestrowany: 2008-02-19

Re: 802.11ax (WIFI 6) Intel Cannon Point-LP CNVi [Wireless-AC] (rev 30)

Przejrzyj ten wątek:
https://forum.dug.net.pl/viewtopic.php?id=31762
Jest w nim poruszone prawie wszystko o wifi. Tylko nie przechodź na stare narzędzia do obsługi interfejsu.

Offline

 

#3  2021-10-10 16:38:36

  wobo - Użytkownik

wobo
Użytkownik
Skąd: Warszawa
Zarejestrowany: 2013-10-16

Re: 802.11ax (WIFI 6) Intel Cannon Point-LP CNVi [Wireless-AC] (rev 30)

Dzięki fnmirk

Oczywiście pozostaje przy systemd-netowrkd
Jak dla mnie jest o wiele przyjemniejszy :)

Większość informacji z wątku próbowałem.
U mnie to tylko potrzeba ulepszenia, a jak wiadomo lepsze jest wrogiem dobrego :)
Więc również nie dam się skusić na tym etapie na wypróbowanie iwd.

Wracając do 802.11ax...
Widzę że opcja jest włączona u mnie w iwlwifi

Kod:

# cat /sys/module/iwlwifi/parameters/disable_11ax
N

A wireless-toools zapewne umożliwia jej implementację. https://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html
Teoretycznie wszystko jest możliwe

Please note that the Wireless Tools (starting with version 19) supports fully IEEE 802.11 parameters and devices, support older style of devices and most proprietary protocols, and are prepared to handle HiperLan as well. More recent versions of course adds more 802.11 support.
But, unfortunately not all drivers support all these features...

Jednakże moja aktualna  wiedza w temacie zarządzania opcjami sterownika jest znikoma więc póki co poczekam na kogoś, kto ma większą wiedzę na ten temat zna konkrety.

Offline

 

Stopka forum

Powered by PunBB
© Copyright 2002–2005 Rickard Andersson
Nas ludzie lubią po prostu, a nie klikając w przyciski ;-)