Forum Debian Users Gang

mateuszj · 2006-11-02 17:22:53

Witam wszystkich!
Mam pytanko do ludzi znających się na sieci.
Jak mogę w Debianie v 3.1 r1 włączyć obsługę karty DWL-520+
jako ACX100 bądź coś innego aby działało mi kodowanie WPA-PSK TKIP.
Ponieważ jestem dość początkującym użytkownikiem prosiłbym o wyrozumiałość i trudniejsze terminy prosiłbym opisać.
Dzięki i pozdrawiam.

jezoo · 2006-11-03 12:36:27

bylo multum razy, no ale dobra, zrob tak:

Kod:

# aptitude install kernel-headers-`uname -r` ndiswrapper-source ndiswrapper-utils module-assistant
# module-assistant auto-install ndiswrapper
# ndiswrapper -i /path/do/sterow/xp/airplus.inf
# modprobe ndiswrapper
# ndiswrapper -m

pozniej musisz skonfigurowac ja tak:

Kod:

# ifconfig wlan0 up
# iwconfig wlan0 ap macTwojegoAP
# iwconfig wlan0 essid TwojejSieci
# iwconfig wlan0 key TwojKlucz restricted
# iwconfig wlan0 mode managed
# iwconfig wlan0 channel nrKanalu
# ifup wlan0

ale wczesniej musisz edytowac plik /etc/network/interfaces

Kod:

auto wlan0
iface wlan0 inet dhcp

mateuszj · 2006-11-03 13:31:38

Okej dzięki, ale czy to będzie obsługiwało kodowanie WPA-PSK TKIP??
Pytałem się dzisiaj speców mówią, że ta karta DWL-520+ nie ma takiej obsługi i że nie da rady nią się łączyć z tym protokołem kodowania???
Dzięki za info.

ba10 · 2006-11-03 14:03:50

I z tego co tu napisano : http://www.dipol.com.pl/sklep/n2700.htm maja racje jest tylko WEP.

mateuszj · 2006-11-03 15:05:10

Mam pytanko,
bo na mój chłopski rozum, to wg. kodu postępowania, to karta sama ustala sobie rodzaj kodowania (WEP czy WPA ...) my tylko podajemy jej dane potrzebne do działania to jest IP, MAC, AP itd.
No to z tego wynikało by że niestety nie można tego kodowania tutaj uruchomić. ??
Dzięki i pozdrawiam.

mateuszj · 2006-11-03 20:20:12

Okej, nie ważne udało mi się opylić tą kartę kupie sobie nową z obsługą WPA-PSK tylko może mi ktoś powie jaka by była dobra dla sieci RESMAN w rzeszowie ??
Dzięki za info.

prunio · 2006-11-21 00:58:19

Jak na razie udało mi się po Debian'em odpalić D-link 520+ za pomocą ndiswrapper'a.
Ale mimo tego net nie działał. Sprawdziłem ping 192.168.1.1 czyli bramki spokojnie dociera ale dalej ani rusz. w pliku /etc/network/interfaces mam coś takiego:

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

iface wlan0 inet static
name Bezprzewodowa karta LAN
address 192.168.1.13
netmask 255.255.255.0
broadcast 192.168.1.255
network 192.168.1.0
gateway 192.168.1.1
wireless_essid WLAN

auto wlan0

co do podpunktu network próbowałem też używać 192.168.1.1
Pytanie brzmi jak to można ustawić tak żeby na stałe już było (co ciekawe przy ustawieniu na DHCP internet działa.
Jeszcze mam drugie pytanie. Musze na kompie założyć kilku użytkowników i zbytnio nie mam pojęcia jak zrobic aby interfejs wlan0 sam się uruchamiał tak żeby każdy użytkownik mógł korzystać z sieci.
Za wszelkie odpowiedzi z góry wielkie dzięki

Lacer · 2006-11-21 01:10:23

witaj
ekspertem nie jestem, ale tak mi się nasunęło - DNS-y masz ustawione?
bo kiedyś ja na tym się wyłożyłem
pozdrawiam

prunio · 2006-11-21 11:39:59

Masz rację ale też od razu na to wpadłem. używałem jakiegoś okienka do konfiguracji sieci i tam też podawałem dns'a. No nic to nie pomagało. Jak już pisałem udało mi się odpalić na DHCP ale za każdym razem muszę wpisywać iwconfig wlan0 up .
I się zastanawiam żeby na tym na razie zakończyć.
Jak można ustawić żeby przy starcie systemu komenda iwconfig włączała interfejs?
Za odpowiedz z góry dziękuje

Lacer · 2006-11-22 01:28:17

hmmm
wydaje mi się, że powinieneś wrzucić skrypt startujący sieć do /etc/init.d a wtedy powinno uruchamiać sieć przy starcie systemu, która powinna być dostępna dla wszystkich użytkowników, którzy się zalogują do systemu

a może się mylę...?
lepiej chyba pójdę spać ;)
pozdrawiam

prunio · 2006-11-22 18:16:27

Walka z siecią ci ąg dalszy: )
1) włączam kompa gdy mam ustawione dhcp to podczas startu pojwaia się że dhcp usiłuje się połączyć na na masce 255.255.255.255 mimo tego że sieć jest ustawiona na 255.255.255.0 , po zalogowaniu pinguje na serwer i nie ma nic. po wydaniu polecenia ifconfig wlan0 192.168.1.1 up , pinguje na 192.168.1.1 i sieć jest 043 ms na odpowiedz. pinguje na wp.pl pokazuje mi że nie znany host. Otwieram ustawienia sieci poatrzę czy są dns'y sa dwa jeden 192.168.1.1 a drugi zdalny leclerka. Co to może byc ??? nie wiem
2) gdy nie mam włączonego dhcp tylko na stałe to też nie mam sieci nie działa ping. reszte robię jak w wyżej . co ciekawe w programie do uatwiania sieci (takie okno w menu system. po zmianie z dhcp na ręczny i zatwierdzeniu tego komputer przestaje się całkowicie do mnie odzywać.
Aktualnie teraz odpaliłem neta (nie wiem jakim cudem) głównie cały czas ustawiam na to samo w iw config ifconfig
i raz działa a drugi raz nie działa nie wiem. Mój ifconfig wygląda tak:

Kod:

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:315 errors:0 dropped:0 overruns:0 frame:0
          TX packets:315 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:73852 (72.1 KiB)  TX bytes:73852 (72.1 KiB)

wlan0     Link encap:Ethernet  HWaddr 00:0D:88:9E:46:24
          inet addr:192.168.1.13  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::20d:88ff:fe9e:4624/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2253 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2199 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2075282 (1.9 MiB)  TX bytes:235970 (230.4 KiB)
          Memory:de010000-de010fff

(tym razem neta ustawiłem ręcznie :)
mój iwconfig wygląda tak:

Kod:

 lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11b  ESSID:"WLAN"
          Mode:Managed  Frequency:2.462 GHz  Access Point: 00:0F:3D:0D:07:73
          Bit Rate:22 Mb/s   Tx-Power:0 dBm   Sensitivity=0/3
          RTS thr:4096 B   Fragment thr:4095 B
          Encryption key:off
          Power Management:off
          Link Quality:98/100  Signal level:134/154  Noise level:0/154
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:184  Invalid misc:319   Missed beacon:0

sit0      no wireless extensions.

a /etc/network/interfaces wygląda tak:

Kod:

lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11b  ESSID:"WLAN"
          Mode:Managed  Frequency:2.462 GHz  Access Point: 00:0F:3D:0D:07:73
          Bit Rate:22 Mb/s   Tx-Power:0 dBm   Sensitivity=0/3
          RTS thr:4096 B   Fragment thr:4095 B
          Encryption key:off
          Power Management:off
          Link Quality:98/100  Signal level:134/154  Noise level:0/154
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:184  Invalid misc:319   Missed beacon:0

sit0      no wireless extensions.

a plik /etc/resolv.conf wygląda tak:

Kod:

search http.hopto.org
nameserver 217.97.141.130

teraz działa, a po reztarcie wszystko jest to samo i niedziała : co zrobić?

bercik · 2006-11-22 20:13:09

1 dhcp chce sie polaczyc z 255.255.255.255 bo ozhnacza to dowolny komputer w sieci (szuka pierwszego serwera dhcp)
2. pokaz /etc/network/interfaces bo przez pomylke dales dwa razy iwconfig
3. co do poprzedniego /etc/network/interfaces to nie wiem czy "auto wlan0" nie powinno byc przed iface wlan0 inet static
4. najlepiej konfiguruj recznie (pliki, ifconfig) bo konfiguratory graficzne czy tez dhcp moze robic dziwne rzeczy (jezeli nie jestes adminem serwera dhcp nie masz wplywu na to co on wysyla ;-) )

prunio · 2006-11-22 21:18:04

Kod:

 This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

iface wlan0 inet static
name Bezprzewodowa karta LAN
wireless_essid WLAN
address 192.168.1.13
netmask 255.255.255.0
broadcast 192.168.1.255
network 192.168.1.0
gateway 192.168.1.1

auto wlan0

tak wygląda /etc/network/interfaces

w sumie tak wklejił to graficzny konfigurator
mam jescze pytanie jak zrobić żeby automatycznie to się odpalało

bercik · 2006-11-23 01:00:04

konfiguracje sieci zapisana w tym pliku powinien uruchamiac skrypt /etc/init.d/networking ... sprawdz moze czy nie jest on przypadkiem wywolywany przed zaladowaniem sterownika karty ... lub nie jest pomijany ...

prunio · 2006-11-23 23:15:03

Jestem dosyć świeży w linuxie i nawet nie wiem gdzie tych logów szukać :)
co jest najśmieszniejsze że codziennie odpala debiana i za każdym raze inaczej odpalam neta
raz na dhcp innym razem na stałym ip tak że już sam nie wiem jak to zrobić
za wszelkie instrukcje łopatologiczne będę wdzięczny.
A cha tak sobie pomyślałem, jak instalowałem tego d-link'a to było napisane że ndiswrapper współpracuje z kernelem powyżej 2.6
więc wziołem płytkę z debainem sarage 3.1 i synaptic wyszukałem taki kernel i go zainstalowałem (pewnie tak się nie robi) nie wiem może to jakoś teraz źle wpływa
pozdrawiam

bercik · 2006-11-24 00:11:15

więc wziołem płytkę z debainem sarage 3.1 i synaptic wyszukałem taki kernel i go zainstalowałem (pewnie tak się nie robi) nie wiem może to jakoś teraz źle wpływa

jezeli dobrze zrozumialem to co napisales to tak sie wlasnie robi :-)

sproboj moze wydac ponizsze komendy jako root

Kod:

ln -s /etc/init.d/ifupdown /etc/rc2.d/S95ifupdown
ln -s /etc/init.d/networking /etc/rc2.d/S96networking

i zobacz czy po nastepnym uruchomieniu systemu bedzie siec ... czy nadal bedzie trzeba ja recznie uruchamiac ...

mateuszj · 2006-11-24 11:26:54

No dobra ale ja chciałem się dowiedzieć jak włączyć kodowanie WPA-PSK na tej karcie :/
Pozdrawiam

prunio · 2006-11-25 23:53:14

No faktycznie zgadza się po wydaniu polecenie

Kod:

su
haslo
cd /etc/init.d/
./networking restart

net odarzu odzywa się
ale po chwilki po 4 (restarcie zauważyłem) że po włączeniu byle jakiej aplikacji (firefox czy xms ) komp przestaje sie odzywać.
chyba tak nie powinno byc ;(

prunio · 2006-11-26 10:18:30

tak wygląda mój syslog po tym jak dowiązałem te pliki według twojego polecenia:

Kod:

Nov 26 10:03:05 localhost kernel: klogd 1.4.1#17, log source = /proc/kmsg started.
Nov 26 10:03:05 localhost kernel: Inspecting /boot/System.map-2.6.8-2-k7
Nov 26 10:03:05 localhost kernel: Loaded 27412 symbols from /boot/System.map-2.6.8-2-k7.
Nov 26 10:03:05 localhost kernel: Symbols match kernel version 2.6.8.
Nov 26 10:03:05 localhost kernel: No module symbols loaded - kernel modules not enabled. 
Nov 26 10:03:05 localhost kernel: Linux version 2.6.8-2-k7 (horms@tabatha.lab.ultramonkey.org) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 Thu May 19 18:03:29 JST 2005
Nov 26 10:03:05 localhost kernel: BIOS-provided physical RAM map:
Nov 26 10:03:05 localhost kernel:  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Nov 26 10:03:05 localhost kernel:  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Nov 26 10:03:05 localhost kernel:  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Nov 26 10:03:05 localhost kernel:  BIOS-e820: 0000000000100000 - 000000002fff0000 (usable)
Nov 26 10:03:05 localhost kernel:  BIOS-e820: 000000002fff0000 - 000000002fff3000 (ACPI NVS)
Nov 26 10:03:05 localhost kernel:  BIOS-e820: 000000002fff3000 - 0000000030000000 (ACPI data)
Nov 26 10:03:05 localhost kernel:  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Nov 26 10:03:05 localhost kernel: 0MB HIGHMEM available.
Nov 26 10:03:05 localhost kernel: 767MB LOWMEM available.
Nov 26 10:03:05 localhost kernel: On node 0 totalpages: 196592
Nov 26 10:03:05 localhost kernel:   DMA zone: 4096 pages, LIFO batch:1
Nov 26 10:03:05 localhost kernel:   Normal zone: 192496 pages, LIFO batch:16
Nov 26 10:03:05 localhost kernel:   HighMem zone: 0 pages, LIFO batch:1
Nov 26 10:03:05 localhost kernel: DMI 2.2 present.
Nov 26 10:03:05 localhost kernel: ACPI: RSDP (v000 VIA694                                    ) @ 0x000f6a20
Nov 26 10:03:05 localhost kernel: ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2fff3000
Nov 26 10:03:05 localhost kernel: ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2fff3040
Nov 26 10:03:05 localhost kernel: ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
Nov 26 10:03:05 localhost kernel: ACPI: PM-Timer IO Port: 0x4008
Nov 26 10:03:05 localhost kernel: Built 1 zonelists
Nov 26 10:03:05 localhost kernel: Kernel command line: root=/dev/hda9 ro 
Nov 26 10:03:05 localhost kernel: Local APIC disabled by BIOS -- reenabling.
Nov 26 10:03:05 localhost kernel: Found and enabled local APIC!
Nov 26 10:03:05 localhost kernel: Initializing CPU#0
Nov 26 10:03:05 localhost kernel: PID hash table entries: 4096 (order 12: 32768 bytes)
Nov 26 10:03:05 localhost kernel: Detected 1662.362 MHz processor.
Nov 26 10:03:05 localhost kernel: Using pmtmr for high-res timesource
Nov 26 10:03:05 localhost kernel: Console: colour VGA+ 80x25
Nov 26 10:03:05 localhost kernel: Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Nov 26 10:03:05 localhost kernel: Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Nov 26 10:03:05 localhost kernel: Memory: 771444k/786368k available (1536k kernel code, 14160k reserved, 697k data, 148k init, 0k highmem)
Nov 26 10:03:05 localhost kernel: Checking if this processor honours the WP bit even in supervisor mode... Ok.
Nov 26 10:03:05 localhost kernel: Calibrating delay loop... 3293.18 BogoMIPS
Nov 26 10:03:05 localhost kernel: Security Scaffold v1.0.0 initialized
Nov 26 10:03:05 localhost kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Nov 26 10:03:05 localhost kernel: CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
Nov 26 10:03:05 localhost kernel: CPU: After vendor identify, caps:  0383fbff c1c3fbff 00000000 00000000
Nov 26 10:03:05 localhost kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Nov 26 10:03:05 localhost kernel: CPU: L2 Cache: 256K (64 bytes/line)
Nov 26 10:03:05 localhost kernel: CPU: After all inits, caps:        0383fbff c1c3fbff 00000000 00000020
Nov 26 10:03:05 localhost kernel: Intel machine check architecture supported.
Nov 26 10:03:05 localhost kernel: Intel machine check reporting enabled on CPU#0.
Nov 26 10:03:05 localhost kernel: CPU: AMD Athlon(tm) XP 2000+ stepping 00
Nov 26 10:03:05 localhost kernel: Enabling fast FPU save and restore... done.
Nov 26 10:03:05 localhost kernel: Enabling unmasked SIMD FPU exception support... done.
Nov 26 10:03:05 localhost kernel: Checking 'hlt' instruction... OK.
Nov 26 10:03:05 localhost kernel: enabled ExtINT on CPU#0
Nov 26 10:03:05 localhost kernel: ESR value before enabling vector: 00000000
Nov 26 10:03:05 localhost kernel: ESR value after enabling vector: 00000000
Nov 26 10:03:05 localhost kernel: Using local APIC timer interrupts.
Nov 26 10:03:05 localhost kernel: calibrating APIC timer ...
Nov 26 10:03:05 localhost kernel: ..... CPU clock speed is 1661.0559 MHz.
Nov 26 10:03:05 localhost kernel: ..... host bus clock speed is 265.0849 MHz.
Nov 26 10:03:05 localhost kernel: checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Nov 26 10:03:05 localhost kernel: Freeing initrd memory: 4468k freed
Nov 26 10:03:05 localhost kernel: NET: Registered protocol family 16
Nov 26 10:03:05 localhost kernel: PCI: PCI BIOS revision 2.10 entry at 0xfb3e0, last bus=1
Nov 26 10:03:05 localhost kernel: PCI: Using configuration type 1
Nov 26 10:03:05 localhost kernel: mtrr: v2.0 (20020519)
Nov 26 10:03:05 localhost kernel: ACPI: Subsystem revision 20040326
Nov 26 10:03:05 localhost kernel: ACPI: IRQ9 SCI: Level Trigger.
Nov 26 10:03:05 localhost kernel: spurious 8259A interrupt: IRQ7.
Nov 26 10:03:05 localhost kernel: ACPI: Interpreter enabled
Nov 26 10:03:05 localhost kernel: ACPI: Using PIC for interrupt routing
Nov 26 10:03:05 localhost kernel: ACPI: PCI Root Bridge [PCI0] (00:00)
Nov 26 10:03:05 localhost kernel: PCI: Probing PCI hardware (bus 00)
Nov 26 10:03:05 localhost kernel: ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
Nov 26 10:03:05 localhost kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
Nov 26 10:03:05 localhost kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 1 *3 4 5 6 7 10 11 12 14 15)
Nov 26 10:03:05 localhost kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
Nov 26 10:03:05 localhost kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Nov 26 10:03:05 localhost kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
Nov 26 10:03:05 localhost kernel: PnPBIOS: Scanning system for PnP BIOS support...
Nov 26 10:03:05 localhost kernel: PnPBIOS: Found PnP BIOS installation structure at 0xc00fbef0
Nov 26 10:03:05 localhost kernel: PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbf20, dseg 0xf0000
Nov 26 10:03:05 localhost kernel: PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
Nov 26 10:03:05 localhost kernel: PCI: Using ACPI for IRQ routing
Nov 26 10:03:05 localhost kernel: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 11 (level, low) -> IRQ 11
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 11 (level, low) -> IRQ 11
Nov 26 10:03:05 localhost kernel: ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 3
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:10.1[B] -> GSI 3 (level, low) -> IRQ 3
Nov 26 10:03:05 localhost kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 10 (level, low) -> IRQ 10
Nov 26 10:03:05 localhost kernel: ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 5 (level, low) -> IRQ 5
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 11 (level, low) -> IRQ 11
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
Nov 26 10:03:05 localhost kernel: VFS: Disk quotas dquot_6.5.1
Nov 26 10:03:05 localhost kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Nov 26 10:03:05 localhost kernel: devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
Nov 26 10:03:05 localhost kernel: devfs: boot_options: 0x0
Nov 26 10:03:05 localhost kernel: Initializing Cryptographic API
Nov 26 10:03:05 localhost kernel: isapnp: Scanning for PnP cards...
Nov 26 10:03:05 localhost kernel: isapnp: No Plug & Play device found
Nov 26 10:03:05 localhost kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
Nov 26 10:03:05 localhost kernel: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Nov 26 10:03:05 localhost kernel: RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Nov 26 10:03:05 localhost kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
Nov 26 10:03:05 localhost kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Nov 26 10:03:05 localhost kernel: input: AT Translated Set 2 keyboard on isa0060/serio0
Nov 26 10:03:05 localhost kernel: NET: Registered protocol family 2
Nov 26 10:03:05 localhost kernel: IP: routing cache hash table of 8192 buckets, 64Kbytes
Nov 26 10:03:05 localhost kernel: TCP: Hash tables configured (established 262144 bind 65536)
Nov 26 10:03:05 localhost kernel: NET: Registered protocol family 8
Nov 26 10:03:05 localhost kernel: NET: Registered protocol family 20
Nov 26 10:03:05 localhost kernel: ACPI: (supports S0 S1 S4 S5)
Nov 26 10:03:05 localhost kernel: RAMDISK: cramfs filesystem found at block 0
Nov 26 10:03:05 localhost kernel: RAMDISK: Loading 4468 blocks [1 disk] into ram disk... |^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^
H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^
H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H
-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^
H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H
^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^
H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|
^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H
^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/
^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H
^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^H^Hdone.
Nov 26 10:03:05 localhost kernel: VFS: Mounted root (cramfs filesystem) readonly.
Nov 26 10:03:05 localhost kernel: Freeing unused kernel memory: 148k freed
Nov 26 10:03:05 localhost kernel: vesafb: probe of vesafb0 failed with error -6
Nov 26 10:03:05 localhost kernel: NET: Registered protocol family 1
Nov 26 10:03:05 localhost kernel: SCSI subsystem initialized
Nov 26 10:03:05 localhost kernel: libata version 1.02 loaded.
Nov 26 10:03:05 localhost kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 26 10:03:05 localhost kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 26 10:03:05 localhost kernel: VP_IDE: IDE controller at PCI slot 0000:00:11.1
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 11 (level, low) -> IRQ 11
Nov 26 10:03:05 localhost kernel: VP_IDE: chipset revision 6
Nov 26 10:03:05 localhost kernel: VP_IDE: not 100%% native mode: will probe irqs later
Nov 26 10:03:05 localhost kernel: VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
Nov 26 10:03:05 localhost kernel:     ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
Nov 26 10:03:05 localhost kernel:     ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
Nov 26 10:03:05 localhost kernel: hda: WDC WD1200BB-00GUA0, ATA DISK drive
Nov 26 10:03:05 localhost kernel: Using anticipatory io scheduler
Nov 26 10:03:05 localhost kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Nov 26 10:03:05 localhost kernel: hda: max request size: 1024KiB
Nov 26 10:03:05 localhost kernel: hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
Nov 26 10:03:05 localhost kernel:  /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
Nov 26 10:03:05 localhost kernel: hdc: LG CD-RW CED-8080B, ATAPI CD/DVD-ROM drive
Nov 26 10:03:05 localhost kernel: hdd: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
Nov 26 10:03:05 localhost kernel: ide1 at 0x170-0x177,0x376 on irq 15
Nov 26 10:03:05 localhost kernel: kjournald starting.  Commit interval 5 seconds
Nov 26 10:03:05 localhost kernel: EXT3-fs: mounted filesystem with ordered data mode.
Nov 26 10:03:05 localhost kernel: Adding 1437776k swap on /dev/hda7.  Priority:-1 extents:1
Nov 26 10:03:05 localhost kernel: EXT3 FS on hda9, internal journal
Nov 26 10:03:05 localhost kernel: hdc: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Nov 26 10:03:05 localhost kernel: Uniform CD-ROM driver Revision: 3.20
Nov 26 10:03:05 localhost kernel: hdd: ATAPI 126X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Nov 26 10:03:05 localhost kernel: input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
Nov 26 10:03:05 localhost kernel: Capability LSM initialized
Nov 26 10:03:05 localhost kernel: mice: PS/2 mouse device common for all mice
Nov 26 10:03:05 localhost kernel: ts: Compaq touchscreen protocol output
Nov 26 10:03:05 localhost kernel: NTFS driver 2.1.15 [Flags: R/O MODULE].
Nov 26 10:03:05 localhost kernel: NTFS-fs warning (device hda1): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
Nov 26 10:03:05 localhost kernel: NTFS volume version 3.1.
Nov 26 10:03:05 localhost kernel: NTFS-fs warning (device hda5): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
Nov 26 10:03:05 localhost kernel: NTFS volume version 3.1.
Nov 26 10:03:05 localhost kernel: NTFS-fs warning (device hda8): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
Nov 26 10:03:05 localhost kernel: NTFS volume version 3.1.
Nov 26 10:03:05 localhost kernel: irda_init()
Nov 26 10:03:05 localhost kernel: NET: Registered protocol family 23
Nov 26 10:03:05 localhost kernel: via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11
Nov 26 10:03:05 localhost kernel: eth0: VIA Rhine II at 0xec00, 00:0d:87:63:36:35, IRQ 11.
Nov 26 10:03:05 localhost kernel: eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
Nov 26 10:03:05 localhost kernel: Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
Nov 26 10:03:05 localhost kernel: via82cxxx: Six channel audio available
Nov 26 10:03:05 localhost kernel: PCI: Setting latency timer of device 0000:00:11.5 to 64
Nov 26 10:03:05 localhost kernel: ac97_codec: AC97 Audio codec, id: VIA97 (Unknown)
Nov 26 10:03:05 localhost kernel: via82cxxx: board #1 at 0xE400, IRQ 10
Nov 26 10:03:05 localhost kernel: usbcore: registered new driver usbfs
Nov 26 10:03:05 localhost kernel: usbcore: registered new driver hub
Nov 26 10:03:05 localhost kernel: USB Universal Host Controller Interface driver v2.2
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 11 (level, low) -> IRQ 11
Nov 26 10:03:05 localhost kernel: uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Nov 26 10:03:05 localhost kernel: uhci_hcd 0000:00:10.0: irq 11, io base 0000d400
Nov 26 10:03:05 localhost kernel: uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
Nov 26 10:03:05 localhost kernel: hub 1-0:1.0: USB hub found
Nov 26 10:03:05 localhost kernel: hub 1-0:1.0: 2 ports detected
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:10.1[B] -> GSI 3 (level, low) -> IRQ 3
Nov 26 10:03:05 localhost kernel: uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
Nov 26 10:03:05 localhost kernel: uhci_hcd 0000:00:10.1: irq 3, io base 0000d800
Nov 26 10:03:05 localhost kernel: uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
Nov 26 10:03:05 localhost kernel: hub 2-0:1.0: USB hub found
Nov 26 10:03:05 localhost kernel: hub 2-0:1.0: 2 ports detected
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 10 (level, low) -> IRQ 10
Nov 26 10:03:05 localhost kernel: uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
Nov 26 10:03:05 localhost kernel: uhci_hcd 0000:00:10.2: irq 10, io base 0000dc00
Nov 26 10:03:05 localhost kernel: uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
Nov 26 10:03:05 localhost kernel: hub 3-0:1.0: USB hub found
Nov 26 10:03:05 localhost kernel: hub 3-0:1.0: 2 ports detected
Nov 26 10:03:05 localhost kernel: usb 1-1: new full speed USB device using address 2
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 5 (level, low) -> IRQ 5
Nov 26 10:03:05 localhost kernel: ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
Nov 26 10:03:05 localhost kernel: ehci_hcd 0000:00:10.3: irq 5, pci mem f08d7000
Nov 26 10:03:05 localhost kernel: ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
Nov 26 10:03:05 localhost kernel: ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
Nov 26 10:03:05 localhost kernel: hub 4-0:1.0: USB hub found
Nov 26 10:03:05 localhost kernel: hub 4-0:1.0: 6 ports detected
Nov 26 10:03:05 localhost kernel: usb 1-1: USB disconnect, address 2
Nov 26 10:03:05 localhost kernel: usb 4-1: new high speed USB device using address 2
Nov 26 10:03:05 localhost kernel: Linux agpgart interface v0.100 (c) Dave Jones
Nov 26 10:03:05 localhost kernel: agpgart: Detected VIA KT266/KY266x/KT333 chipset
Nov 26 10:03:05 localhost kernel: agpgart: Maximum main memory to use for agp memory: 690M
Nov 26 10:03:05 localhost kernel: agpgart: AGP aperture is 128M @ 0xd0000000
Nov 26 10:03:05 localhost kernel: cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
Nov 26 10:03:05 localhost kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Nov 26 10:03:05 localhost kernel: pciehp: acpi_pciehprm:_SB_.PCI0 evaluate _BBN fail=0x5
Nov 26 10:03:05 localhost kernel: pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
Nov 26 10:03:05 localhost kernel: shpchp: acpi_shpchprm:_SB_.PCI0 evaluate _BBN fail=0x5
Nov 26 10:03:05 localhost kernel: shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
Nov 26 10:03:05 localhost kernel: Real Time Clock Driver v1.12
Nov 26 10:03:05 localhost kernel: input: PC Speaker
Nov 26 10:03:05 localhost kernel: inserting floppy driver for 2.6.8-2-k7
Nov 26 10:03:05 localhost kernel: Floppy drive(s): fd0 is 1.44M
Nov 26 10:03:05 localhost kernel: FDC 0 is a post-1991 82077
Nov 26 10:03:05 localhost kernel: parport: PnPBIOS parport detected.
Nov 26 10:03:05 localhost kernel: parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
Nov 26 10:03:05 localhost kernel: ndiswrapper version 1.1 loaded (preempt=yes,smp=no)
Nov 26 10:03:05 localhost kernel: ndiswrapper: driver airplus (D-Link,06/05/2003,3.0.23.4) loaded
Nov 26 10:03:05 localhost kernel: ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 11 (level, low) -> IRQ 11
Nov 26 10:03:05 localhost kernel: ndiswrapper: using irq 11
Nov 26 10:03:05 localhost kernel: wlan0: ndiswrapper ethernet device 00:0d:88:9e:46:24 using driver airplus, configuration file 104C:8400:1186:3B01.5.conf
Nov 26 10:03:05 localhost kernel: wlan0: encryption modes supported: WEP
Nov 26 10:03:05 localhost kernel: NET: Registered protocol family 17
Nov 26 10:03:06 localhost named[3609]: starting BIND 9.2.4 -u bind
Nov 26 10:03:06 localhost named[3609]: using 1 CPU
Nov 26 10:03:06 localhost named[3609]: loading configuration from '/etc/bind/named.conf'
Nov 26 10:03:06 localhost kernel: NET: Registered protocol family 10
Nov 26 10:03:06 localhost kernel: Disabled Privacy Extensions on device c02fc1a0(lo)
Nov 26 10:03:06 localhost kernel: IPv6 over IPv4 tunneling driver
Nov 26 10:03:06 localhost named[3609]: listening on IPv4 interface lo, 127.0.0.1#53
Nov 26 10:03:06 localhost lwresd[3625]: starting BIND 9.2.4
Nov 26 10:03:06 localhost lwresd[3625]: using 1 CPU
Nov 26 10:03:06 localhost lwresd[3625]: loading configuration from '/etc/bind/lwresd.conf'
Nov 26 10:03:06 localhost lwresd[3625]: none:0: open: /etc/bind/lwresd.conf: file not found
Nov 26 10:03:06 localhost lwresd[3625]: loading configuration from '/etc/resolv.conf'
Nov 26 10:03:06 localhost lwresd[3625]: none:0: open: /etc/bind/rndc.key: permission denied
Nov 26 10:03:06 localhost lwresd[3625]: couldn't add command channel 127.0.0.1#953: permission denied
Nov 26 10:03:06 localhost lwresd[3625]: none:0: open: /etc/bind/rndc.key: permission denied
Nov 26 10:03:06 localhost lwresd[3625]: couldn't add command channel ::1#953: permission denied
Nov 26 10:03:06 localhost lwresd[3625]: lwres listening on 127.0.0.1#921
Nov 26 10:03:06 localhost named[3609]: command channel listening on 127.0.0.1#953
Nov 26 10:03:06 localhost named[3609]: command channel listening on ::1#953
Nov 26 10:03:06 localhost named[3609]: zone 0.in-addr.arpa/IN: loaded serial 1
Nov 26 10:03:06 localhost named[3609]: zone 127.in-addr.arpa/IN: loaded serial 1
Nov 26 10:03:06 localhost named[3609]: zone 255.in-addr.arpa/IN: loaded serial 1
Nov 26 10:03:06 localhost named[3609]: zone localhost/IN: loaded serial 1
Nov 26 10:03:06 localhost named[3609]: running
Nov 26 10:03:06 localhost lwresd[3625]: running
Nov 26 10:03:08 localhost lpd[3711]: restarted
Nov 26 10:03:08 localhost kernel: NET: Registered protocol family 5
Nov 26 10:03:08 localhost papd[3724]: restart (2.0.2)
Nov 26 10:03:08 localhost papd[3724]: CUPS support enabled (1.1)
Nov 26 10:03:08 localhost afpd[3726]: Registering CNID module [last]
Nov 26 10:03:08 localhost afpd[3726]: Registering CNID module [cdb]
Nov 26 10:03:08 localhost afpd[3726]: Registering CNID module [dbd]
Nov 26 10:03:08 localhost afpd[3726]: Loading ConfigFile
Nov 26 10:03:08 localhost afpd[3726]: Finished parsing Config File
Nov 26 10:03:08 localhost afpd[3726]: main: atp_open: Cannot assign requested address
Nov 26 10:03:08 localhost afpd[3726]: dsi_tcp: hostname 'gorki' resolves to loopback address
Nov 26 10:03:08 localhost afpd[3726]: dsi_tcp (Chooser will not select afp/tcp)nCheck to make sure gorki is in /etc/hosts and the correct domain is inn/etc/resolv.conf: Success
Nov 26 10:03:08 localhost afpd[3726]: ASIP started on 0.0.0.0:548(4) (2.0.2)
Nov 26 10:03:08 localhost afpd[3726]: DSIConfigInit: Error registering afp://0.0.0.0/?NAME=localhost&ZONE= with SRVLOC
Nov 26 10:03:08 localhost afpd[3726]: uam: loading (/usr/lib/netatalk/uams_dhx.so)
Nov 26 10:03:09 localhost afpd[3726]: uam: uam not found (status=-1)
Nov 26 10:03:09 localhost afpd[3726]: uam: loading (/usr/lib/netatalk/uams_clrtxt.so)
Nov 26 10:03:09 localhost afpd[3726]: uam: uams_clrtxt.so loaded
Nov 26 10:03:09 localhost afpd[3726]: uam: loading (/usr/lib/netatalk/uams_randnum.so)
Nov 26 10:03:09 localhost afpd[3726]: uam: uam not found (status=-1)
Nov 26 10:03:09 localhost afpd[3726]: uam: "Cleartxt Passwrd" available
Nov 26 10:03:15 localhost rpc.statd[3856]: Version 1.0.6 Starting
Nov 26 10:03:15 localhost rpc.statd[3856]: statd running as root. chown /var/lib/nfs/sm to choose different user 
Nov 26 10:03:15 localhost /usr/sbin/cron[3861]: (CRON) INFO (pidfile fd = 3)
Nov 26 10:03:15 localhost /usr/sbin/cron[3862]: (CRON) STARTUP (fork ok)
Nov 26 10:03:15 localhost /usr/sbin/cron[3862]: (CRON) INFO (Running @reboot jobs)
Nov 26 10:03:16 localhost dhclient: Internet Software Consortium DHCP Client 2.0pl5
Nov 26 10:03:16 localhost dhclient: Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium.
Nov 26 10:03:16 localhost dhclient: All rights reserved.
Nov 26 10:03:16 localhost dhclient: 
Nov 26 10:03:16 localhost dhclient: Please contribute if you find this software useful.
Nov 26 10:03:16 localhost dhclient: For info, please visit http://www.isc.org/dhcp-contrib.html
Nov 26 10:03:16 localhost dhclient: 
Nov 26 10:03:16 localhost dhclient: sit0: unknown hardware address type 776
Nov 26 10:03:17 localhost kernel: wlan0: no IPv6 routers present
Nov 26 10:03:17 localhost dhclient: sit0: unknown hardware address type 776
Nov 26 10:03:17 localhost dhclient: Listening on LPF/wlan0/00:0d:88:9e:46:24
Nov 26 10:03:17 localhost dhclient: Sending on   LPF/wlan0/00:0d:88:9e:46:24
Nov 26 10:03:17 localhost dhclient: Sending on   Socket/fallback/fallback-net
Nov 26 10:03:17 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8
Nov 26 10:03:25 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8
Nov 26 10:03:33 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 19
Nov 26 10:03:52 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8
Nov 26 10:04:00 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 15
Nov 26 10:04:15 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 2
Nov 26 10:04:17 localhost dhclient: No DHCPOFFERS received.
Nov 26 10:04:17 localhost dhclient: No working leases in persistent database. 
Nov 26 10:04:17 localhost dhclient: Exiting. 
Nov 26 10:04:18 localhost udev[3910]: creating device node '/dev/vcs2'
Nov 26 10:04:18 localhost udev[3918]: creating device node '/dev/vcsa2'
Nov 26 10:04:18 localhost udev[3936]: creating device node '/dev/vcs3'
Nov 26 10:04:18 localhost udev[3944]: creating device node '/dev/vcsa3'
Nov 26 10:04:18 localhost udev[4096]: creating device node '/dev/vcsa6'
Nov 26 10:04:18 localhost udev[4026]: creating device node '/dev/vcs4'
Nov 26 10:04:18 localhost udev[4027]: creating device node '/dev/vcsa4'
Nov 26 10:04:18 localhost udev[4028]: creating device node '/dev/vcs5'
Nov 26 10:04:18 localhost udev[4029]: creating device node '/dev/vcsa5'
Nov 26 10:04:18 localhost udev[4105]: creating device node '/dev/vcs7'
Nov 26 10:04:18 localhost udev[4111]: creating device node '/dev/vcsa7'
Nov 26 10:04:18 localhost udev[4127]: removing device node '/dev/vcs5'
Nov 26 10:04:18 localhost udev[4138]: removing device node '/dev/vcsa5'
Nov 26 10:04:18 localhost udev[4139]: removing device node '/dev/vcs4'
Nov 26 10:04:18 localhost udev[4030]: creating device node '/dev/vcs6'
Nov 26 10:04:18 localhost udev[4170]: removing device node '/dev/vcs3'
Nov 26 10:04:18 localhost udev[4172]: removing device node '/dev/vcsa3'
Nov 26 10:04:18 localhost udev[4174]: removing device node '/dev/vcs2'
Nov 26 10:04:18 localhost udev[4176]: removing device node '/dev/vcsa2'
Nov 26 10:04:18 localhost udev[4178]: removing device node '/dev/vcs6'
Nov 26 10:04:18 localhost udev[4180]: removing device node '/dev/vcsa6'
Nov 26 10:04:18 localhost udev[4182]: creating device node '/dev/vcs3'
Nov 26 10:04:18 localhost udev[4184]: creating device node '/dev/vcs4'
Nov 26 10:04:18 localhost udev[4186]: creating device node '/dev/vcs5'
Nov 26 10:04:18 localhost udev[4188]: creating device node '/dev/vcsa3'
Nov 26 10:04:18 localhost udev[4145]: removing device node '/dev/vcsa4'
Nov 26 10:04:18 localhost udev[4193]: creating device node '/dev/vcsa2'
Nov 26 10:04:18 localhost udev[4195]: creating device node '/dev/vcs6'
Nov 26 10:04:18 localhost udev[4197]: creating device node '/dev/vcsa4'
Nov 26 10:04:18 localhost udev[4199]: creating device node '/dev/vcsa6'
Nov 26 10:04:18 localhost udev[4190]: creating device node '/dev/vcs2'
Nov 26 10:04:18 localhost udev[4191]: creating device node '/dev/vcsa5'
Nov 26 10:04:18 localhost udev[4217]: removing device node '/dev/vcs7'
Nov 26 10:04:18 localhost udev[4218]: removing device node '/dev/vcsa7'
Nov 26 10:04:19 localhost udev[4235]: creating device node '/dev/vcs7'
Nov 26 10:04:19 localhost udev[4236]: creating device node '/dev/vcsa7'
Nov 26 10:04:43 localhost kernel: via_audio: ignoring drain playback error -11
Nov 26 10:04:43 localhost kernel: via_audio: ignoring drain playback error -11
Nov 26 10:05:01 localhost gconfd (prunio-4629): uruchamianie (wersja 2.8.1), pid 4629, użytkownik "prunio"
Nov 26 10:05:01 localhost gconfd (prunio-4629): Uzyskano adres "xml:readonly:/etc/gconf/gconf.xml.mandatory" do źródła konfiguracji tylko do odczytu na pozycji 0
Nov 26 10:05:01 localhost gconfd (prunio-4629): Uzyskano adres "xml:readwrite:/home/prunio/.gconf" do zapisywalnego źródła konfiguracji na pozycji 1
Nov 26 10:05:01 localhost gconfd (prunio-4629): Uzyskano adres "xml:readonly:/etc/gconf/gconf.xml.defaults" do źródła konfiguracji tylko do odczytu na pozycji 2
Nov 26 10:06:00 localhost dhclient: Internet Software Consortium DHCP Client 2.0pl5
Nov 26 10:06:00 localhost dhclient: Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium.
Nov 26 10:06:00 localhost dhclient: All rights reserved.
Nov 26 10:06:00 localhost dhclient: 
Nov 26 10:06:00 localhost dhclient: Please contribute if you find this software useful.
Nov 26 10:06:00 localhost dhclient: For info, please visit http://www.isc.org/dhcp-contrib.html
Nov 26 10:06:00 localhost dhclient: 
Nov 26 10:06:00 localhost dhclient: sit0: unknown hardware address type 776
Nov 26 10:06:01 localhost dhclient: sit0: unknown hardware address type 776
Nov 26 10:06:01 localhost dhclient: Listening on LPF/wlan0/00:0d:88:9e:46:24
Nov 26 10:06:01 localhost dhclient: Sending on   LPF/wlan0/00:0d:88:9e:46:24
Nov 26 10:06:01 localhost dhclient: Sending on   Socket/fallback/fallback-net
Nov 26 10:06:01 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 3
Nov 26 10:06:04 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 4
Nov 26 10:06:08 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6
Nov 26 10:06:14 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13
Nov 26 10:06:27 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14
Nov 26 10:06:41 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 16
Nov 26 10:06:41 localhost dhclient: DHCPOFFER from 192.168.1.1
Nov 26 10:06:41 localhost last message repeated 4 times
Nov 26 10:06:43 localhost dhclient: DHCPREQUEST on wlan0 to 255.255.255.255 port 67
Nov 26 10:06:43 localhost dhclient: DHCPACK from 192.168.1.1
Nov 26 10:06:43 localhost dhclient: bound to 192.168.1.13 -- renewal in 10800 seconds.
Nov 26 10:06:55 localhost kernel: via_audio: ignoring drain playback error -11

bercik · 2006-11-26 14:24:36

net odarzu odzywa się
ale po chwilki po 4 (restarcie zauważyłem) że po włączeniu byle jakiej aplikacji (firefox czy xms ) komp przestaje sie odzywać.
chyba tak nie powinno byc ;(

rozumiem ze po utworzeniu tych linkow net dziala po starcie kompa ... tylko gdy zaczyna sie go uzywac to jest calkowity zwis ... przypuszczalbym ze jest bad sterownika karty i masz kernel panic ... odpal jakis soft do kozystania z sieci na konsoli (wget, w3m, ...) i zobzacz czy w chwili zwisu cos wyzuci na konsole ...

PS zlam w ostatnim poscie ta linijke z "H^H|^H/^H-^H^H|^H/^H-^H^H|^H/^H-^" bo sie ciezko czyta ...

prunio · 2006-11-26 16:17:49

rozumiem ze po utworzeniu tych linkow net dziala po starcie kompa ... tylko gdy zaczyna sie go uzywac to jest calkowity zwis ...

no nie
teraz trochę to już rozgryzłem:
to jest tak włączam kompa neta nie ma. Kopete ma komunikat nie znaleziono serwera DNS.
pisze /etc/init.d/networking restart
i net pojawia się
zwisy były tylko przy ręcznym ustawianiu ip.
To jest tak jak by przy starcie systemu nie pobierał adresu z serwera.

Forum Debian Users Gang

Ogłoszenie

#1 2006-11-02 17:22:53

mateuszj - Użytkownik

WiFi + DWL-520+ + WPA-PSK TKIP

#2 2006-11-03 12:36:27

jezoo - Dzięcioł

Re: WiFi + DWL-520+ + WPA-PSK TKIP

Kod:

Kod:

Kod:

#3 2006-11-03 13:31:38

mateuszj - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#4 2006-11-03 14:03:50

ba10 - Członek DUG

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#5 2006-11-03 15:05:10

mateuszj - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#6 2006-11-03 20:20:12

mateuszj - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#7 2006-11-21 00:58:19

prunio - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#8 2006-11-21 01:10:23

Lacer - Członek DUG

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#9 2006-11-21 11:39:59

prunio - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#10 2006-11-22 01:28:17

Lacer - Członek DUG

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#11 2006-11-22 18:16:27

prunio - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

Kod:

Kod:

Kod:

Kod:

#12 2006-11-22 20:13:09

bercik - Moderator Mamut

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#13 2006-11-22 21:18:04

prunio - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

Kod:

#14 2006-11-23 01:00:04

bercik - Moderator Mamut

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#15 2006-11-23 23:15:03

prunio - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#16 2006-11-24 00:11:15

bercik - Moderator Mamut

Re: WiFi + DWL-520+ + WPA-PSK TKIP

Kod:

#17 2006-11-24 11:26:54

mateuszj - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#18 2006-11-25 23:53:14

prunio - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

Kod:

#19 2006-11-26 10:18:30

prunio - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

Kod:

#20 2006-11-26 14:24:36

bercik - Moderator Mamut

Re: WiFi + DWL-520+ + WPA-PSK TKIP

#21 2006-11-26 16:17:49

prunio - Użytkownik

Re: WiFi + DWL-520+ + WPA-PSK TKIP

Stopka forum